Question about 1999 Dodge Intrepid

2 Answers

How do you repair a throttle positioning censor

I have a 99 dodge intrepid and i need to know how to repair or remove and put the new throttle on?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1999 3.2 Dodge Intrepid, will die at the end of the exit ramps and at stoplights and sign. what should I look for? engine is not the one that came with the car so computer won't read.

Posted on Jul 02, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 64 Answers

Reach in under the dash, under the steering wheel and pull the cable end off the gas peddle. Open the hood, disconnect the cable end off the throttle body, then haul the cable through the firewall from the engine side. Replace by doing the reverse.

Posted on Jul 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 99 Dodge Intrepid and when I start it, starts @ 4000 rpms what do I need to check? Just put in new battery and starter.


I guess what you are saying is that it idles too fast. When the battery has been dead for some time the ECU must re-learn the engine parameters, but this seems a bit excessive. You may have a stuck Idle Air Control (IAC) motor, bad TPS, bad coolant temp sensor, stuck throttle body, cable or gas pedal or maybe the MAF was damaged installing the new battery.

Mar 28, 2016 | Dodge Cars & Trucks

2 Answers

Location of the throttle position sensor


the censor is located adjacent to the throttle control linkage, and has a 3 wire connection plug

May 30, 2010 | 2004 Dodge Dakota

2 Answers

CAN NOT LOCATE THE CRANKSHAFT POSITION CENSOR ON MY 1996 INTREPID


It should be on the transmission by the passenger side of car. It has three wires connected to it.
1998 Dodge Intrepid
the crank sensor is on the passenger side of the car on the back of the engine. Check right up there by the transmission housing.
1994 Dodge Intrepid 3.3 liter

Jan 01, 2010 | 1996 Dodge Intrepid

1 Answer

My '99 Intrepid won't run. Replaces the throttle


looks like your intrepid has what is know as a driveability problem
1. electric fuel pump is failing
2. injectors are mis-firing due to clogs: 1 or more has failed
3. someone has been naughty and dumped something in your fuel tank while you slept

Oct 22, 2009 | 1999 Dodge Intrepid

1 Answer

To remove an alternator on a 1998-99 Intrepid, on drivers side


FIRST OF ALL.TURN OFF RADIO SO YOU WONT LOSE RADIO CODE.FOR THE 2.7L ENGINE.DISCONNECT NEGATIVE BATTERY CABLE.REMOVE THE LOWER PLASTIC SPLASH SHIELD.REMOVE TRANSMISSION COOLER AND POSITION IT ASIDE.REMOVE THE LOWER RADIATOR CROSSMEMBER SUPPORT.LOOSEN BUT DO NOT REMOVE.ADJUSTING T BOLT AND THE PIVOT BOLT.LOOSEN DRIVE BELT ADJUSTING BOLT.REMOVE OR DISCONNECT THE FOLLOWING.DRIVE BELT.REMOVE ALTERNATOR ELECTRICAL WIRES.REMOVE PIVOT BOLT CAREFUL NOT TO LOSE THE SPACER.REMOVE THE ALTERNATOR. NOW THE 3.2L AND 3.5L ENGINES REMOVE THE NEGATIVE BATTERY CABLE.THEN REMOVE THE LOWER MOUNTING BOLT AND PIVIT BOLT.REMOVE DRIVE BELTTENSION BOLT THEN DRIVE BELT.REMOVE BRACKET LOWER MOUNTING BOLT AND PIVOT BOLT.THEN REMOVE THE ALTERNATOR + ALTERNATOR FIELD CIRCUIT PLUG + ALTERNATOR B+ TERMINAL NUT AND WIRE.THEN PUT EVERYTHING BACK VISA VERSA.

Sep 18, 2009 | 1999 Dodge Intrepid

1 Answer

Location of Position Sensor in 1997 Dodge intrepid 3.5?


If your talking throttle position sensor, look at front of throttle body with air intake hose off, and see throttle plate in front, has a shaft going through it, your throttle position sensor is on the end of that shaft & will have a wiring connector to it. Who said it needs a new one?

Aug 09, 2009 | 1997 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Intrepid Logo

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...