Question about 2004 Kia Sorento

Open Question

How do I change front and rear brake pads on a Kia Sorento

Kia Sorento 3.5 automatic 04 plate. Do I have to use a special tool?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: replace rear brake pads on a 2000 grand marquis

rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Posted on Mar 15, 2009

Junoon007
  • 1011 Answers

SOURCE: How do you compress rear brake caliper?

Dear Sir/madam,

The pistons on the rear brake calipers SCREW in to the caliper. There are notches on the inner edge of the piston face. engage the notches with a large needle nose plier or a large flat washer and turn clockwise (as you face the piston) to turn the piston in.
There is a special tool that is available at your local autoparts store that is absolutely necessary and will save you a ton of time and aggravation. Using a needle nose plier or washer does not allow you to apply enough pressure unless your are the incredible hulk.

thanks
Good luck

Posted on Oct 24, 2008

  • 71 Answers

SOURCE: Rear Brakes on a 2002 GMC 2500HD.??

You will need a large allen socket or torqes (sp?) socket to loosen the caliper bolts; you can get at auto parts places. Other than that you will likely need a medium to large deep throat C clamp to force the fluid back to the resevoir by squeezing the calipers back in the body. Do this slowly as there may be check valves to over come with the fluid return. I am not aware of other special stuff.

Posted on Jan 30, 2009

emissionwiz
  • 75817 Answers

SOURCE: Are spark plugs on 2005 Kia Sorento on top of

yes they are on the top under the coils each plug has, no spec tools required, just remove the coils to get at the plugs.

Posted on Jul 01, 2009

turboKia
  • 55 Answers

SOURCE: having problem changing rear brake pads on 2006 kia spectra

yes ... its a tool that you can buy at any well stocked auto parts store. Its cubed shaped, about an inch on each side, Its used to screw in the caliper piston

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear rotor will not come off kia sorento 07


You only have two possiblities

The lip on both sides of the rotor that
the pads are hung on & rust from never
removing all rust from hub & using anti-seize

You have to take apart brakes once a year to
get rid of rust, even if no other attention is needed

If the pads are out-- hit the rotor with 2x4 to break the rust

Jan 28, 2013 | 2007 Kia Sorento 4x4

1 Answer

Anything special about changing front pads on audi a3? I've done honda, acura and toyota's.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Aug 25, 2010 | 2007 Audi A3

1 Answer

I just had the front brake pads replaced and the mechanic said that the rear pads were fine, but now they are making the shushing sound, even when I am driving and not braking. What should I do?


first port of call is to return to the guy who said all was ok on the rear brakes of a sorento there are brake pads for your service/foot brake, but the handbrake works on a sepperate system. there are brake shoes within the rear brake discs which are solely for the parking brake... have these been overtightened ar just full of dust, my advice is to take it back, if no joy then try someone who knows about this system
any advice i can help with then ask.
regards
roger

Jun 21, 2010 | 2005 Kia Sorento

1 Answer

2006 Kia Spectra 5 rear brake disc replacement


you need a special tool avalable at most parts stores. its a disc brake piston turning tool. you have to rotate piston clockwise while pushing in on piston. you can fabricate something that enguages the slots and push and turn till all the way in.make sure to note position of slots and put them in same place as was before or the pin on the pads wont enguage the slot

May 10, 2010 | Cars & Trucks

2 Answers

Brake Pad Replacement,2004 VW Touareg,V6 instructions


yes, you need a piston retract tool for the rear cylinders. rear piston must turn clockwise as it is being retracting.

Jun 11, 2009 | 2004 Volkswagen Touareg

2 Answers

Successfully changed front brakes but when i went to change rear brakes the caliper seems to be stuck.what can i do?


your rear brake has most likely a drum in hat style brake.

The caliper is not stuck, you need a special tool to rotate the piston of the brake caliper and depress it down. It is connected to your parking brake, that is why this security measure was taken.

the special tool looks like this :

9d6f12d.gif

a ratchet fits in the center hole and depending on the style of piston you have you will need a specific side of this "cube" tool.
you may need to slide the pads out to see the piston.

I hope this helps, Goodluck!

May 11, 2009 | 2000 Lincoln Continental

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

4 Answers

2002 Jetta Brakes


On one of the front driver side pads there is a sensor for low pads. He either did not hook it back up or got a lose connection to it.

May 29, 2008 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
2004 Kia Sorento Logo

Related Topics:

2,423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...