Question about 1992 Jeep Wrangler

1 Answer

What type of oil does the transfer case of a 1992 Jeep wrangler take? Also where is the drain plug to check the level?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jeep Master
  • 75,797 Answers

It uses ATF..

Posted on Jun 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 jeep wrangler 5 speed 4 cylinder shifts has


won't, not want , right?
the xfr case rear tail shaft is dead.
the 5speed box , must be in gear, is it, did you confirm it , by checking the 5speed, shifter bottom linkage that it really is in gear, did you try all 5 gears?
that be first , then see if the transfer case fails.
same way. same tests.

your post is a contradiction.
if the input to the xfr spins, the output must too, in 2wd mode. (both)
if not the xfr case has issues.
or simple linkage.

Oct 11, 2014 | 1992 Jeep Wrangler

1 Answer

Transfer case oil


usually ATF oil,fill to plug level

Jun 22, 2014 | 1993 Jeep Wrangler

1 Answer

How many qts of oil do i need


Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES

Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Feb 02, 2013 | 1984 Jeep CJ7

1 Answer

Need to replace 1992 Jeep wrangler clutch


It's time consuming but not difficult.If you are not a do it yourselfer take it to a reputable mechanic.If you are then get a relevant Haynes repair manual, a ****** jack and floor jack, a set of standard and metric sockets and wrenches, a buddy to help balance the ******/transfer case when you pull/install them, a smooth surface to work on ( even a 5/8" sheet of plywood will do) and pick a nice day to do it. An air compressor/ impact tools will save a pile of time and if you want to change the oils, on my Jeep the transfer case drain nut is 30mm while the ****** drain is a 15/16".

Dec 18, 2010 | 1992 Jeep Wrangler

2 Answers

What kind of gear oil is required for my 1992 jeep wrangler 5 speed transmission/transfer case and how many quarts will it require


Transmission generally takes a bit less than two quarts, Use 75/90 gear lube in that (in very cold climates you can add a small amount of automatic trans fluid to keep it flowing on cold starts) Transfer case takes a bit over one quart and takes dextron mercon 3. When filling either, fluid is full when on a level surface it begins to come out of the fill hole while filling. When changing either, always make sure you can open the fill plug before draining so you know you can replace what you removed.

Sep 06, 2010 | 1992 Jeep Wrangler

1 Answer

What is the capacity of the transfer case and exactly what fluid do i use


GM Full-Size Trucks 1980-1987 Repair Guide

Transfer Case - FLUID RECOMMENDATIONS
The type of lubricant used in the transfer case varies with model year and type of transfer case. Refer to the list below for the type that applies to your truck.

1980
Conventional transfer cases require SAE 80W or SAE 80W-90 GL-5 gear lubricant.
Full time systems use SAE 10W-30 or 10W-40 engine oil.
1981
Conventional transfer cases require DEXRON®II transmission fluid.
1982-85
All transfer cases require DEXRON®II transmission fluid.
1986-87
All transfer cases except the K30/35 series require DEXRON®II transmission fluid.

For fluid recommendations for the K30/35 transfer cases refer to the owner's manual.
LEVEL CHECKS

fb6e8b4.jpg
Fig. Model 208 Transfer Case

Check the four wheel drive transfer case lubricant level every 4 months or 6,000 miles.
  1. With the truck parked on a level surface and the parking brake firmly applied, remove the filler plug from the rear of the transfer case (behind the transmission). Be careful not to take out the drain plug at the bottom.
  2. If lubricant trickles out, there is enough. If not, carefully insert a finger and check that the level is up to the edge of the hole, EXCEPT in full time four wheel drive cases should be 1 /2 in. below the hole.
Lubricant may be added, if necessary, with a funnel and tube, or a squeeze bulb.



DRAIN AND REFILL
Part Time Systems
No intervals are specified for changing transfer case lubricant, but it is a good idea for trucks that are worked hard or driven in deep water.
  1. With the transfer case warmed up, park on a level surface and apply the parking brake.
  2. Slide a pan of a least 6 pts. capacity under the case drain plug.
  3. Remove the filler plug from the rear of the transfer case (behind the transmission). Remove the drain plug from the bottom.
  4. Wipe the area clean and replace the drain plug.
  5. Add lubricant with a suction gun or squeeze bulb. Conventional transfer cases require SAE 80W-90 GL-5 Gear Lubricant.
  6. When the lubricant level is up to the bottom of the filler hole, replace the plug.
Full Time Four Wheel Drive
The full time system requires oil changes at regular intervals, according to the amount and type of work done by the unit. Trucks used for normal on-off road work should have the transfer case oil changed at 24,000 mile intervals. When used for heavy duty work, trailer towing, snowplowing, and the like, the interval should be halved to 12,000 miles. If the truck is exposed to extremely dusty or muddy conditions, the oil should be changed at 1,000 mile intervals.
The transfer case oil must be hot before changing. Drive the truck until the engine has reached normal operating temperature, and park on a level surface.
  1. Slide a pan of at least 8 pts. capacity under the case drain plug.
  2. Remove the filler plug.
  3. Remove the lowest bolt from the front output shaft rear bearing retainer cover, and allow the lubricant to drain. Be careful; the oil will be hot. There may be a drain plug. If so, remove that instead.
  4. Remove the six bolts on the left (driver's) side of the case which secure to P.T.O. (power take-off) cover. Remove this cover and allow the lubricant to drain out.
  5. Remove the speedometer driven gear from the upper left rear corner of the case.
  6. Use a suction gun to remove as much lubricant as possible from the case cover location and the speedometer gear location.
  7. Install the speedometer driven gear, the P.T.O. cover, and the lowest bolt or drain plug.
  8. Add approximately seven pints of oil through the filler plug opening. The proper oil to use is 10W-30 or 10W-40 engine oil.
  9. Check the fluid level and add sufficient oil to raise the level to 1 /2 in. below the filler plug opening. Replace the plug, and wipe the surfaces of the case and skid plate to remove any excess oil. Drive the truck and check for leaks.

I really hope help ypou woth this (remember rated this help) Good luck.

Oct 16, 2009 | 1983 Chevrolet Silverado

1 Answer

What type of oil,oil filter and transmission fluid do i need? for a straight, 5 speed 93 jeep wrangler?


Jeep Wrangler/YJ 1987-1995 Repair Guide

Engine Oil

d0a6433.jpg

Fig. 1: Be sure to select the proper API quality classification and SAE viscosity grade of engine oil (10W-30)


Oil FIlter (K&N sample)
02b0418.jpg

HP-2004 work for 2.5L and 4.0L


Manual Transmission
The level of lubricant in the transmission should be maintained at the filler hole on all manual transmissions. This hole is on the right side. When you check the level in the transmission, make sure that the vehicle is level so that you get a true reading. When you remove the filler plug, lubricant should run out of the hole. Replace the plug quickly for a minimum loss of lubricant. If lubricant does not run out of the hole when the plug is removed, lubricant should be added until it does. Replace the plug as soon as the lubricant reaches the level of the hole.

4a317e4.jpg

Fig. 1: Manual transmission fill and drain hole plugs

DRAIN AND REFILL
Remove the drain plug which is at the bottom of the transmission. Allow all the lubricant to run out before replacing the plug. Replace the case with the correct viscosity oil. All manual transmissions use SAE 75W-90 API quality Grade GL-5 gear lubricant. Tighten the fill hole plug to 27 ft. lbs. (37 Nm).


I hope help you with this (rermember rated this help) Good luck.

Oct 12, 2009 | 1993 Jeep Wrangler

2 Answers

What kind of ATF goes in my 1992 cherokee?


Use ATF+4

Do not use Dexron or Mercon

Aug 08, 2009 | 1992 Jeep Cherokee Sport

1 Answer

Transfer case maintentance


I assume you are looking for how often maintenance is required. Every 30,000 miles or 24 monthss requires a drain and refill.

Specs: RECOMMENDED LUBRICANT AND FILL LEVEL Recommended lubricant for the NV231 transfer case is Mopart DexronII, or ATFPlus3, type7176. Approximate lubricant fill capacity is 1.2liters (2.5pints).The fill and drain plugs are both in the rear case.Correct fill level is to the bottom edge of the fill plug hole. Be sure the vehicle is level to ensure an accurate fluid level check.

Aug 08, 2009 | 2000 Jeep Wrangler

4 Answers

Dont know were to put in new transmission oil on a 1992 Jeep Wrangler


the plug of the transmission of 1992 jeep is under the transmission case .

Apr 20, 2009 | 1992 Jeep Wrangler

Not finding what you are looking for?
1992 Jeep Wrangler Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...