Question about 2002 Volkswagen Golf

1 Answer

Clutch slips on my bora i had a new clutch and flywheel fitted about 18months ago done about 24,000 and its now slipping. warantee was only for one year. surely a clutch should do more than 24,000 miles.

Posted by on

  • yadayada
    yadayada May 11, 2010

    factory parts?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 77 Answers

Yes it should unless it took a beating

Posted on Jul 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tell if a flywheel is bad


most flywheel faults are heat related caused by a slipping clutch . Remove the transmission and inspect for , blue color heat spots . small cracks. scores caused by a worn out driven plate, run out check with a dial gauge. most flywheels can be machined as good as new . All ways fit a new replacement clutch kit with a new throw out bearing.

Oct 31, 2014 | Cars & Trucks

1 Answer

New clutch and pressure plate installed 6 months ago why should it be slipping again


To honest- you know more, than we could even guess at

I would say the job you paid for wasn't done, as I would have done
it, six months ago

Repairs Shops don't always machine the flywheel & never balance
any of the assy & who knows the parts quality

Yes----- I once owned a trans shop, so I have seen some
not so good employees & managers at work & it isn't pretty,
sloppy work & lack of knowledge is my guess at your expense

Mar 05, 2013 | Daewoo Nubira Cars & Trucks

2 Answers

I have a 96 cavalier 2.2 5 spd


the pressure plate might have gone bad or need resurfacing if glazed.
also the flywheel could be glazed.

Jan 30, 2013 | Chevrolet Cavalier Cars & Trucks

2 Answers

Clutch seems to be slipping I put everything in new


Sounds like bad clutch but that should have been replaced when fly wheel fly wheel worked on.

Jan 15, 2013 | 1992 Jeep Wrangler

1 Answer

1998 Nissan 200sx new clutch slips when hot


The cable is probably too tight,andnot allowing the pressure plate to use all of its clamping force. This will also wear out the new release bearing.

Sep 25, 2012 | Nissan 200SX Cars & Trucks

1 Answer

My clutch is slipping - rpms acclerate but car has no power barely moves. how expensive is it to replace a manual clutch?


$900.00 if the entire job is done correctly

The flywheel machined
New pressure plate
New clutch disc
New Slave Cylinder
New Throw out brg

Mar 19, 2011 | 2004 Kia Spectra

3 Answers

Clutch is slipping and needs adjustment how


Sorry but all the newer cars don't have a adjustment's they are all hydraulic clutches. They have adjustments for the cable but it wont help the clutch. It needs a new clutch and maybe a flywheel if it's burnt and slippin. I hope this helps ya.

Oct 31, 2010 | 1999 Hyundai Accent

1 Answer

NEW CLUTCH SLIPPING ON 2004 V6 HOLDEN RODEO


did you bleed the hydralic clutch system on this vehicle? = air in system or not bleed properly.
most of the flywheels for this model were not to be machined...... however it is ok to machine these only slightly but you must machine the surface the clutch plate contacts with the same amount as the outer raised section the pressure plate bolts to.
new flywheels have painted stamped writing saying do not machine...so if hydralic system is ok find out about flywheel.
also may pay to check clamping force of pressure plate most clutch places can do this or some workshops that is if fingers on pressure plate are all at the same height, not broken or cracked..

Dec 01, 2009 | 2004 Isuzu Rodeo

1 Answer

Peugeot 106 1.5D. the clutch was slipping so new clutch fitted 2 weeks ago. It was still slipping so that garage replaced the clutch again. Guess what? It is still slipping. Any idea what is going on?


Yes clutch pedal should start to drive about 1inch off the floor and when driving keep your foot away from the pedal,/ also when new clutch is fitted did they fit a complete clutch assy /and did they surface grind the flywheel as if it was badly worn on the 1st one then the new one wouldent last very long.
as when the clutch starts to drive 1" from the floor clutch is good /when it engages right out its buggered and slips so ask about the f/wheel

Oct 02, 2009 | 1991 Peugeot 405

2 Answers

Clutch slipping when it get hot


Check the adjustment of the clutch push rod. It is the rod that connects the clutch pedal to the clutch master cylinder.

Dec 22, 2008 | 1992 Isuzu Amigo

Not finding what you are looking for?
2002 Volkswagen Golf Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...