Question about 1997 Ford Taurus

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

Please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal

  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    I need to replace a rear seat belt in a 1997 Ford - 2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Posted on Jul 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove back seat of hhr 2006


Rear Seat Replacement

showgif.do?image=1592810

tif.gif

Callout

Component Name
Notice: Refer to Fastener Notice in the Preface section.
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
Preliminary Procedure Remove the rear compartment floor stowage compartment tray. Refer to Rear Floor Trim Plate Replacement .
1
Nut, Rear Seat (Qty: 6)
Tip
Roll the seat forward enough to get access to the nut that attaches the center seat belt assembly to the floor.
Tighten
45 N?·m (33 lb ft)
2
Bolt, Rear Seat (Qty: 3)
Tip

  1. Adjust the seat forward or rearward to access the bolts.
  2. Remove the plastic trim pieces to gain access to the nuts.
Tighten
45 N?·m (33 lb ft)
3
Rear Seat Assembly

Oct 28, 2015 | Seat Cars & Trucks

1 Answer

Wireing diagram for pcm for 1994 ford tarsus


We do not have wiring diagrams. You can access them for a small fee i am told here: alldatadiy.com

Jun 12, 2012 | 1994 Dodge Colt

2 Answers

I need the diagram for the serpantine belt on a


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 1997 Ford Windstar with the 3.8L V6 Engine. The Page of Diagrams on the Link also has the 3.0L Engine Diagrams, and included the various engine options (AC, No AC etc.). AND it has additional informational and directional diagrams that will be very helpful to you in the future.

http://www.2carpros.com/car_repair_information/year/1997/make/ford/model/windstar/1997_ford_windstar_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 02, 2010 | 1997 Ford Windstar

1 Answer

Ford f 150 serpentine belt routing diagram


CLICK on the following LINK. It has all the Diagrams for your Belt that you will need.
If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Thanks!

http://www.2carpros.com/car_repair_information/year/1997/make/ford/model/f-super_duty/1997_ford_f-super_duty_drive_belt_routing_diagram.htm

Feb 09, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Need diagram for timing belt for 1997 ford ranger


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1997/make/ford/model/ranger/1997_ford_ranger_timing_belt_diagram_marks.htm

Oct 29, 2009 | 1997 Ford Ranger SuperCab

1 Answer

Serpentine belt diagram


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1997/make/ford/model/econoline/1997_ford_econoline_drive_belt_routing_diagram.htm

Oct 15, 2009 | 1997 Ford Econoline

1 Answer

Need a diagram for serpentine belt for ford f-250 7.3


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/1997/make/ford/model/pickup/1997_ford_pickup_drive_belt_routing_diagram.htm

Oct 08, 2009 | 1997 Ford F250 SuperCab

1 Answer

Reaching rear seat belt on 1997 crown victoria


Lap belt or shoulder harness? Lap belt - remove rear seat bottom by pushing in on bottom edge of the seat cushion and lifting. This will expose the lap belt and its anchor. Shoulder belt should be accessible via trunk compartment. If not then you'll have to remove the back of the rear seat to get to it.

Oct 04, 2009 | 1997 Ford Crown Victoria

1 Answer

I have a 1997 Ford Escort. The rear seat belt is stuck


make sure that the rear seats are properly locked into rear catches as this can stop your seatbels from working if ok then sounds like your seatbelt is faulty req new seatbelt.

Mar 07, 2009 | 1997 Ford Escort

Not finding what you are looking for?
1997 Ford Taurus Logo

Related Topics:

1,622 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...