Question about 2005 Mazda Tribute

1 Answer

Had brake booster replaced ,now no cruise control working..

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 154 Answers

The brake light switch is out of adjustment, the cruise thinks you are stepping on the brake. you will need to get the plunger on the switch to the right length and then your cruise should work

Posted on Aug 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While driving hit resume cruise control and the car speed up to 100 and brakes would not work. Had to shut engine off in middle of freeway, what could it be?


Could be a faulty cruise control servo activator. The power to move the cruise control Actuator is most likely coming from the Brake power hydraulic booster vacuum pipe and if the cruise control vacuum servo is failing and leaking in air you lose the brakes power hydraulics.
check the vacuum pipe coming off the power booster brake master cylinder vacuum pipe you may find a tee connector in the vacuum main pipe and follow it to see where it goes to. Could be a break in the cruise control vacuum hose but if it is only happening when the cruise control is activated a fault or leak in the cruise control servo device is the main suspect. Which you should find at the other end of the cruise control vacuum hose.

Jan 31, 2016 | 2004 Oldsmobile Alero

1 Answer

97 chevy no brake lts or cruise


If you are stating no brake lights or cruise control check the sensors attached to the brake pedal stop ..One sensor if for cruise control and one is for the brake lights....

Feb 17, 2015 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Cruise control does not work after having power booster replaced


thers somethin the mech didnt reconnect--chec fluid in steerin--probly a vacuum line is at issue--call that joker up and tellum and also ask why he didnt test drive

Sep 05, 2012 | 2005 Mercury Mariner

1 Answer

I recently replaced my brake booster. After the


hello there:
you may have over looked the vacuum line for the cruise control that hooks up to or close to brake booster hope this helps you out..sincerely D.Jones

Jun 06, 2010 | 1997 Ford Taurus

1 Answer

1999 Lincoln Continental. The cruise will turn on but will not set. Recently had Sears replace the brake booster, is there any cruise components that have to be removed or disconnected to complete this...


The cruise control mechanism is in the area of the booster, so it is possible they had to remove it to get to the booster. It may just be unplugged.

May 17, 2010 | Cars & Trucks

2 Answers

Cruise control problem


There are 3 places on the Rav4 where fuses can be located and checked. for the cuise control.

The back of the cruise control stacking switch has been know to fail (fall apart) and Toyota issued a TSB with replacement switch.

if it is the fuses then they most likely are related to cruise control system: Stop, Dome, Gauge and Igniton
The interior fuse box
The main engine fuse box (by brake fluid)
Cruise control ECU is under the glovebox.
Cruise control actuator is under hood (by driver side brake fluid/booster)Throttle position sensor (to detect if your foot is on gas pedal)
Cruise control switch on the clutch pedal too (if you have 5spd manual)
Brake lights are the deactivate signal for the cruise control


Aug 13, 2009 | 1998 Toyota RAV4

1 Answer

I have a 1998 C1500 and the problem is my crusie control does not work and my brake light do not work. replaced the brake booster and that fixed the problem for a little while but problem is back.


You might have a bad brake light switch located at the top of the brake pedal, there's also a cruise control switch mounted next to the brake light switch.

Apr 09, 2009 | 1998 Chevrolet C1500

1 Answer

Leaking brake fluid + Faulty cruise control


If you see fluid at the rear of the master where it attaches to the power booster then the cylinder itself is leaking. It's not often that the container leaks.
The hissing noise is very likely coming from the power booster. This must be replaced. If cruise has a vacuum hose that connects to hose to booster it's possible that vacuum loss at booster is causing the cruise problem.If you are going to do the booster, have a good tech take a look at it first. they are expensive and you don't want to change it on my advice alone...I'm not there and can't hear it!

Mar 24, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Cruise control wont work


normally the brake switch is the issue with these trucks. it is located under the dash where the brake pedal meets the linkage to the brake booster.

Jan 04, 2009 | 1997 GMC Sierra

Not finding what you are looking for?
2005 Mazda Tribute Logo

443 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...