Question about 2004 Mazda 6

1 Answer

Drivers side low beam is out. How do I change it?

Drivers side low beam is out. Manual says to bring it to a dealership. Is there a way to change it myself?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Its possible if you have small hands. Its not worth going to the dealership. Just pay attention on how you remove the cap that you turn and you are good. Its not hard. Ive done it a couple times already. Just be very careful when placing the bulb in its place without actually touching the bulb. Pay special attention on how the blown bulb is set.

Posted on Jul 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

2 Answers

Head light have low but when using high does not work just on one side drivers side


HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Dec 20, 2015 | 2004 Nissan Sentra

2 Answers

Prius high beam lights work but low beam lights do not work?


On a 2008 Prius, If both High beams work but only one side has working low beams, then it is most likely a fuse. So before breaking your knuckles to change the bulb, check the fuse first. I found out the hard way as my mom distressed to me that her drivers side headlights were out. So without checking to see if low and high were working, I proceeded to remove and replace the bulb - ouch! There are 4 10 amp fuses that protect the circuits for low/high beam function. They are under the hood in the fuse box on the drivers side and they are marked on the box cover. Check them before changing the bulb.

Oct 29, 2012 | 2006 Toyota Prius

1 Answer

My high beams work but low beams 1 is not working


Check the headlight relays- your owners manual will show you where they are.

Mar 11, 2012 | 1995 Ford Explorer

1 Answer

Drivers side low beam is out but high beam works fine


Sounds like a bad bulb or connector to the bulb. I would check the connector make sure its not burnt or melted and then change the bulb.

Apr 14, 2009 | Honda Civic Cars & Trucks

1 Answer

Driver side low beam not working


You will need to change the bulb.

Dec 21, 2008 | 1998 Honda Prelude

1 Answer

Changing low beam headlight bulb on 2005 chrysler sebring


you can change the passanger side with little difficulty however the drivers side you need to remove power cell from it's bracket and move aside in order to access light.

Nov 12, 2008 | 2005 Chrysler Sebring Conv

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...