What is the torque specifiction on the connecting rod cap on 1996 jeep 5.2 motor

The torque specifications for the main bearings and connecting rod bearings in a Ford WL/WLT 2.5L Turbo engine may vary depending on the specific model year and engine configuration. However, as a general guideline, here are the torque specifications for the main bearings and connecting rod bearings in this engine:
Main bearings:

1. Torque the main bearing cap bolts in three stages in the following sequence:Stage 1: 30 Nm (22 lb-ft)
   Stage 2: 80 Nm (59 lb-ft)
   Stage 3: 90 degrees
2. After the final torque of 90 degrees, check the bolt stretch with a torque angle gauge. The stretch should be between 0.15mm and 0.30mm.

Connecting rod bearings:

1. Torque the connecting rod cap bolts in two stages in the following sequence:Stage 1: 30 Nm (22 lb-ft)
   Stage 2: 90 degrees
2. After the final torque of 90 degrees, check the bolt stretch with a torque angle gauge. The stretch should be between 0.15mm and 0.30mm.

It is important to note that these torque specifications are general guidelines and may vary based on the specific model year and engine configuration. Always refer to the manufacturer's service manual or consult a certified mechanic for the exact torque specifications for your specific vehicle

The conrod torque specification for the MR20 engine in the Nissan X-Trail T31 is 27-31 Nm (20-23 lb-ft) for the connecting rod bolts.
It's important to follow the correct torque sequence and use a torque wrench to ensure the bolts are tightened to the correct specification. Always refer to the manufacturer's service manual or consult a qualified mechanic if you're not comfortable performing engine work yourself.

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

This is a Toyota engine. Follow the link to a torque spec chart http://www.torkspec.com/torkspecme.aspx?KI=42-1.8L-109ci-S4

100 foot pounds

97 Jeep Cherokee 4WD 4.0L I6
Connecting Rod Bearing Cap Torque - 33 lbs.-ft. (final torque)

Main bearing cap bolts are 58 Nm or 43 ft-lb. The sequence is like this

7 3 1 5 9

8 4 2 6 10

Con rod cap nuts are 24 Nm or 18 ft lb, then, an additional 1/4 turn.

These figures are with an oil film on the parts, not dry, and should be reached in three steps right round, not all at once.

I need accurate torque specifications for rod and I need accurate torque specifications for rod and main bearing caps for a 2.0 liter eclipse turbo 90 help plis

TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.