Question about Isuzu Rodeo

1 Answer

I just put a new head gasket on my 2.6lt isuzu motor, now it wont start. I have spark at the plugs. Do I need to bleed the fuel injectors somehow after I had them off??

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Make sure you have connect the fuel injectors
electrical connecters in the correct injector.
You don't have to bleed them. Also the plug wires. If so it should start.

Posted on Jun 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do i need to bleed the injector pump on my isuzu bighorn 4gj2 after replacing the head? as it wont fire


anytime you disconnect the fuel rail, and if it has a bleeder/test port (looks like a tire Valve), Then it needs to be bled before fuel will reach the injectors. Also check Spark plug ignition as well make sure grounds have been returned properly.

Oct 13, 2015 | Isuzu Cars & Trucks

1 Answer

Replaced motor, starting hard. runs fine . how do I check fuel pressure


Doubtful you have a fuel pressure problem if the car runs well, poor starting can be a few things , poor air circulation air filter needs cleaning or replacing, poor injector flow warn injectors or just dirty fuel additive sometimes clears this , poor spark plugs not firing under pressure ok when started . for diesel cars you don't say what car it is , poor glow plugs . bad fuel filter , air leaks in fuel pump , poor injectors . and especially with diesel poor compression due to worn rings or head gasket failure . You may even have just have disturbed the engine earth strap when you replaced your starter motor .

Jul 03, 2015 | Cars & Trucks

2 Answers

I have a 1987 ford ranger the engine turns over but it wont start


Spark at plugs? Fuel filter? Pressure on injector delivery line? Pressure relief valve? You may be able to measure fuel pressure at the pressure relief valve location. and return line. If you have spark, I'd say it's a fuel supply problem

Dec 21, 2014 | Ford Cars & Trucks

1 Answer

I have a 1998 gmc jimmy 4.3 6cylinder 4x4 I blew


What I've seen done to test an injector is to pull it, and swap it for another cylinder. If the miss moves, then the injector is bad. If the miss stays on #5, then the problem isn't the injector.

Sep 17, 2014 | 1998 GMC Jimmy

1 Answer

Toyota prado 2001 v6 5vz engine, will start but wont run


OK - You confirmed the thermostat was causing the overheating? Sounds like fuel injectors - but check the spark plugs and ignition coils first.

Jan 18, 2013 | Toyota Land Cruiser Cars & Trucks

1 Answer

1996 Isuzu Rodeo 2.6L wont start


check the firing order
you could be 180 degrees out

May 08, 2017 | Cars & Trucks

2 Answers

My Mitsubushi Space Star Car won't Start. What can I try?


spark plugs are deep in the head yet you should get all the the old fuel out first, stale fuel wont ignite and will also clogg fuel filter. you need a mix of atleast 70% new fuel even then its not good for the injecters. If its a manual gearbox a tow start is a quick fix although no go for auto's. cant be much wrong if car was fine when parked, plugs-fuel-filter and possibly fuel pump for sure. If that doesnt fix take plug out put in lead and crank engine to be sure you have spark even just put any plug you know works in lead leaving your plugs in engine just to check for spark y turning over engine looking for spark on plug good spark will be blue but any spark is good.

Jun 16, 2012 | Mitsubishi Cars & Trucks

1 Answer

Have just put new head gasket in our 4ze1 after blowing a heater hose. motor now hard to start and wont idle but runs well out on the open road. does everything right on the open road - pulls up hills etc...


plug gap 25 th ,too wider gap and it will be hard starting from cold ,as for idle then this could be a vacumn hose perished or not reconnected when head gasket changed ,or a vacumn pipe has been damaged whilst changing the head gasket follow then all back even the best of us inadvertantly damage things or drop a bolt somewhere that always rattles afterwards

Dec 19, 2010 | 1991 Isuzu Rodeo

4 Answers

Isuzu 4JX1 EngineWont Start after replacing new injector


my isuzu bighorn will not start after changing valve seals and head gasket and after setting timing it still will not start. do you have a solution.

Aug 09, 2008 | 1999 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...