Question about 1992 Ford Ranger

1 Answer

Ranger only works on high speed

Went to junk yard replaced the motor and replaced the switch assembly on stering wheel. still only works on high. (HELP)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Take it in to the dealship for diagnosis... too many possible causes for this problem.

Posted on Jun 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

96 ford exsplorer 4wd blinking lights


If after driving a little bit the 4wd light starts blinking then I believe one (or both) of your HALL sensors are bad or have picked up some metal filings.

I believe the light is blinking because your GEM computer doesn't think both driveshafts are going the same speed.

I think one of your HALL sensors is fooling the GEM into thinking one of the driveshafts is stopped all the time

When you are stopped the computer thinks everything is OK (because the other driveshaft is stopped also)

When you are moving the GEM tries to get both driveshaft spinning the same speed but the sensor isn't responding

It takes 5 minutes to change the rear sensor (you have to cut the old one off and splice in the new one. Sealing the splice with liquid electrical tape)

The front sensor is hardr becasue you have to remove the shift motor on the transfer case

also for the 4wd system there is a TOD(torque on demand relay) that might be bad

Jan 22, 2015 | 1996 Ford Explorer

1 Answer

On my 1994 S-10 Blazer, the AC/Heater stopped blowing on high speed about 2 years ago. By switching the speed control quickly back and forth, sometimes High would work. But not anymore. I had the A/C...


Sometimes the electrical connecter burns on the back side of your switch. You can get just the switch and replace it and repair the connecter when possible.

Aug 12, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Worn out colum or gear box


go to the junk yard and find a used gear box, and replace it..

Dec 31, 2009 | 1997 Ford F350 Crew Cab

2 Answers

Cae was stolen and recovered. they broke the ignition. how do I replace the steering column Is it necessary to replace the entire column?


Hi,

I am sure this would work by just replacing the ignition switch, not the entire steering column.

However it also depends on how bad was it broken.

Please let us know for future assistance.
Thanks
Fame !

Jul 10, 2009 | 1997 Dodge Intrepid

1 Answer

Blow motor working only on high speed


Go to a Junk yard and find a replacement switch(all three Switches).. The new ones will run you about $ 125.00

Jun 25, 2009 | 1999 Chevrolet Malibu

1 Answer

Heat only when switch is on high


replace the blower motor speed control resistor.

Mar 06, 2009 | 2004 Hyundai Santa Fe

2 Answers

Front blower motor doesn't work, rear does


yes, all blower motors have them to control their speed, High, medium, low.. etc. I earn nothing by helping you, but my rating, a fixya rating and I will walk you through this

Dec 20, 2008 | 2005 Chrysler Town & Country

3 Answers

I have a 1998 Dodge 1500 why does the heater/ac blower motor only work on high, do I need to replace the motor?


The motor is fine, the blower resistor is the most likely cause. All fan speeds except high go through the resistor.

Dec 08, 2008 | Dodge Pickup Cars & Trucks

Not finding what you are looking for?
1992 Ford Ranger Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...