Question about 2001 Chrysler Voyager

1 Answer

How does one remove the ingnitionswitch from column???? It is exposed can not find a release point/catch... This is in a 1983 New YORKER

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 176 Answers

  1. Disconnect battery ground cable.
  2. Remove under panel sound deadener.
  3. Disconnect speed control switch.
  4. Remove two switch attaching screws, then rotate switch 90°and pull-up to disengage switch from rod.
  5. When installing new switch push up gently on switch relieve slack in rod system

Posted on Jun 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the procedure for removing the power steering pump


1982 Chrysler New Yorker Power Steering Belt Removal ...

? 0:35
www.youtube.com/watch?v=vZD17F_ao-o
Jan 18, 2015 - Uploaded by Kerman 559 Sanchez
1982 Chrysler New Yorker Power Steering Belt Removal ...1990 Chrysler New Yorker Fifth Avenue Start Up, Engine, and In Depth Tour ...

1990 chrysler new yorker 3.3 power steering pump change ...

www.fixya.com/cars/t15056742-1990_chrysler_new_yorker_3_3_power
Nov 18, 2012 - SOURCE: 1990 new yorker alternator replacement. You are right aboutremoving the motor mount. You have to support the engine with a jack.
images for 1990 Chrysler New Yorker remove power

Oct 20, 2015 | 1990 Chrysler New Yorker

1 Answer

Find a Diagram for 1989 Lincoln Towncar 4 Door Fusebox


this is for the base model


FUSE PANEL IDENTIFICATION (1983-90 LINCOLN TOWN CAR) The fuse panel is located in the instrument panel to the left of the steering column. To expose fuse panel, remove lower steering column finish panel.

Fuse & Circuit Breaker Identification

· 1 - 15 Amp Stoplights, Hazard Warning Lights, Speed Control Module, Trailer Tow Relays, Cornering Light Relay (1983-89)
· 2 - 8.25 Amp (Circuit Breaker) Windshield Wiper/Washer
· 3 - Blank
· 4 - 15 Amp Taillights, Side Marker, License Light, Parking & Coach Lights, Cluster Illumination, Trailer Tow Relay
· 5 - 15 Amp Turn Signal & Back-Up Lights, Trailer Tow Relay, Cornering Light Relays, Heated Rear Window Relay, Rear Defrost (1988-90), A/C Clutch & ATC Module (1990), Load Leveling (1990)
· 6 - 20 Amp Heated Rear Window Control, Speed Control Module & Clock Display, Illuminated Entry Module, Power Window & Police Accy Relays, Fuel Filler Door Release (1983-87), A/C Clutch & Cornering Lights (1983-89), Deck Lid Release (1987-90), Tripminder
· 7 - 10 Amp Daytime Running Light Resistor (1990)
· 8 - 15 Amp Dome LP-Clock, Key Warning Chimes & Electric Mirrors, Courtesy & Visor Mirror Lights, Autolight & Illuminated Entry Modules, Tripminder, Electronic Radio Memory, Trunk & Underhood Lights
· 9 - 15/30 Amp Heater Blower (15 Amp), AC/ATC Blower (30 Amp)
· 10 - Blank
· 11 - 20 Amp Radio & Power Antenna, CB Radio
· 12 - 20 Amp Door Cigarette Lighters, Power Seats & Door Locks (30 Amp), Tailgate Power Window (1983-89)
· 13 - 5 Amp Illuminated Outside Thermometer, Instrument Panel Lights
· 14 - 20/25 Amp (Circuit Breaker) Flash-To-Pass, Sun Roof, Power Windows
· 15 - 10 Amp Taillights, Parking, Side Marker/Coach, License Lights
· 16 - 20 Amp Horn & Front Cigarette Lighter
· 17 - 15 Amp Electronic Cluster, Message Center
· 18 - 10 Amp Warning Indicator Lights, Throttle Solenoid Positioner, Low Fuel Module & Autolight System, Dual Timer Buzzer & Electronic Chimes, Electronic Message Center

25415475-rnxj1x0ziuckirrqexm4r53n-3-0.gif

Feb 11, 2015 | 1989 Lincoln Town Car

1 Answer

How do i change a serpentine belt on my 1990 new yorker


Write a diagram of the pulleys and belt direction release the tensioner or alternator adjusting bolt remove old belt and fit new one, check idler pulley bearings for noise and wear.

Nov 15, 2014 | 1990 Chrysler New Yorker

1 Answer

Front end shaking at idle


MAY HAVE BROKEN MOTOR MOUNT

Dec 05, 2012 | 1983 Chrysler New Yorker

1 Answer

Fuse box location


fuse box located below steering column on back of panel. remove 4 phillips screws from acess panel to expose fuse block.

Apr 19, 2012 | 1983 Dodge Pickup

1 Answer

How do i tear apart my steering column in my 84 dodge pickup so i can change my ignition switch?


  1. NON TILT WHEEL
  2. Remove the steering wheel.
  3. Remove the turn signal switch.
  4. Unfasten the two screws that release the buzzer switch (if equipped), then remove the switch.



0900c15280052e49.jpg

Fig. Fig. 2: Removing the ignition buzzer

  1. Remove the retaining screw and lift the ignition lock cylinder lamp out of the way.



0900c15280052e4a.jpg

Fig. Fig. 3: Ignition key lamp

  1. Remove the bearing housing.
  2. Detach the coil spring.
  3. Remove the lock plate from the shaft.



0900c15280052e4b.jpg

Fig. Fig. 4: Lock lever plate removal

  1. Unfasten the 2 retaining screws and lift the lock lever guide plate to expose the lock cylinder release hole.
  2. Insert the key and place the lock cylinder in the LOCK position. Remove the key.
  3. Insert a thin punch into the lock cylinder release hole and push inward to release the spring-loaded lock retainer. At the same time, pull the lock cylinder out of the column.



0900c15280052e4c.jpg

Fig. Fig. 5: Depress the lock plate which will expose the lock cylinder release hole

  1. Remove the 3 retaining screws and lift out the ignition switch.

To install:
  1. Position the ignition switch in the center detent position (OFF).
  2. Place the shift lever in PARK.
  3. Feed the wires down through the space between the housing and jacket. Position the switch in the housing and install the 3 retaining screws.



0900c15280052e4d.jpg

Fig. Fig. 6: Lock levers and spring assembly installed

  1. Place the lock cylinder in the LOCK position, and press it into place in the column. It will snap into position.
  2. The remainder of assembly is the reverse of disassembly.

Aug 14, 2011 | 1984 Dodge Pickup 4WD

1 Answer

Where is neutral ground switch located on the 1991 Chrysler New Yorker.


I am not aware of a neutral ground switch, I presume that you are speaking of the neutral safety switch. These switches are typically located at the lower end of the steering column, and sometimes at the shift lever input on the transmission, itself.

Anything along the shift linkage, from the trans to the steering column locking tube can be connected to this switch.

Dec 31, 2010 | 1991 Chrysler New Yorker

1 Answer

How to change the headlight bulb on a 1995 chrysler new yorker


look inside the engine bay behind the headlight, you will see a large rubber weather seal over the rear of the headlight which covers the wiring and spring to release the bulb, check it out
remove the multi wire plug b4 removing the bulb ok

Jun 24, 2010 | 1995 Chrysler New Yorker

1 Answer

1987 chrysler new yorker blinker not working replaced the lights


Just saw this post. Maybe you've already found the answer by now. I have an 87 new yorker. i have the manual that came with the car. The fuse box should be under the stearing column to the left. Cover pops off. The turn signal lamps take a 20 amp fuse. it goes in cavity #10

Dec 10, 2008 | 1987 Chrysler New Yorker

1 Answer

98 S10 5 speed. How do I get rid my daytime running lights, I have already removed 2 fuses that are supposed to controll them but they still come on when I release the parking brake, I dont want to cut...


If you set your parking brake to the first "click" or as soon as the pedal catches, it will turn off the DRL's but not actually engage the brake. Make sure you stop at the very first point the emergency brake pedal will stay down.

Jul 23, 2008 | 1983 Chevrolet S-10

Not finding what you are looking for?
2001 Chrysler Voyager Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...