Question about 2000 Chevrolet Impala

1 Answer

2ooo Impala Front powerwindows move up and down freely, but only come back up half way when putting themm up.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 43 Answers

Might I suggest one easy thing to try? Buy a can of silicone spray and douse the weatherstrips liberally. If the car has been outside most of its life the weatherstrip can dry out and create a drag as the glass tries to go up and down. It won't hurt anything to try and I've seen it make a huge difference.

Posted on Jun 30, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2ooo chevy impala no crank anti-thieft problem

Turn the key on and leave it on until the theft light blinks or goes off.It should start then.This could take 10 to 20 minutes.

Apr 08, 2018 | 2000 Chevrolet Impala

1 Answer


Mr. MOMODU, as you said looks like the brakes master cylinder is faulty. is blocking the front wheels.Renew the brakes Master cylinder and bled the system and would be okay.

Apr 22, 2014 | 1998 Ford Windstar

1 Answer

2000 monto carlo ss service tracking light comes on when i depress brakes and i notice rear brake rotors have deep groves and pad looks worn if i change both how will i no if calipers are ok

Your rear caliper is made to slide on it's bracket to allow your rear pads to move freely and evenly and to keep the brakes from dragging when not being used. If it won't slide on the bracket you can disassemble the two halfs of your caliper (when off the car) clean them up well (sandpaper, wire brush, brake parts cleaner, sos pads ect) and put antiseize or grease the slide pins. There are usually two slide pins and they have rubber gromets around them. If seized they may have caused the rear roters to wear badly.

Sep 19, 2011 | 2004 Chevrolet Impala

1 Answer

The belt continues to break beacause its off the tensioner half way and is getting pinched by the water pump pulley....what should i do to get the belt on track(but i also have the belt put on correctly

Is the tensioner in line with the rest of your pulleys? Does it move back and forth freely? If not , replace the tensioner. Do all the other pulleys appear to be in line, and do they move freely? Hope this helps, TJ

Aug 06, 2011 | 1996 Mercury Sable

1 Answer

2001 Impala, strong right to left vibration felt in the front end ONLY when accelerating, NOT felt through steering wheel NOT felt when coasting, or slowing down, strait or turning vehicle tracks...

Has to be a drive axle,most likely an inner joint,should be able to feel the play if one is bad (jacked up to let the wheel spin freely).
Also. If the front suspension is weak,or lowered, the CV axle will bottom out in the inner plunge cup and make a terrible vibration.

Feb 02, 2011 | 2001 Chevrolet Impala

1 Answer

More pronounced when cold. Shifts hard and winds out before shifting. Ist shift at approx. 35mph, with second shift at approx. 45mph, 3rd shift almost immediate after second. Is the point of shifting...

I would check your kick down leaver on the transmission. Make sure it is working freely. Sometimes the kick down leaver and the shifter leaver will bind together and cause the kick down leaver to get stuck. Sometimes when this happens you can feel hard spots in the shifter or hard spots in the gas pedel. or the gas pedel will be super easy to push. Block all the wheels front and back turn the key on. DO NOT START IT put it in drive then go under it and make sure the kick down leaver is moving freely. The reason it has to be in drive when you do this is because it may move freely in park but not when its in drive. The kick down leaver should move back and forth almost effortlessly. If it don't that is your problem. Get some WD40 lube it up and move it back and forth till it move back and forth easily. It would help to put some spray greese on it after its free to prevent it from happening again. If this is not you problem there is a band in the transmission that can cause this too. The tabs on the band where you make the adjustment on it will sometime bend apart over time causing the band to be out of adjustment. To fix this you will have to pull the pan and valve body bend the tabs back and readjust the band. Good Luck 4 thumbs up is appreciated if this helps.

Dec 02, 2010 | 1992 Dodge Dakota

1 Answer

Front power window switch seems loose

The mtor is wearing out. You will have to mnually grab and pull it up

Jun 24, 2009 | 2002 Chevrolet Impala

1 Answer


This could due the power window cable snap out its place you need to get it serviced or the motor should be replaced , this is one of the major cause for the power window ................................

Good luck..........

Jul 04, 2008 | 2001 Chevrolet Impala

Not finding what you are looking for?
2000 Chevrolet Impala Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides