Question about 1999 Dodge Intrepid

1 Answer

Location of the resistor for hvac blower? - 1999 Dodge Intrepid

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,927 Answers

The blower resister is located in the blower box/usally two screws maybe 3 with multi wire plug in

Posted on Jun 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower stays on after key is removed, now a/c works in front once I hit the highway.


Which of these systems does your vehicle have ?
HVAC Systems - Automatic
Blower Motor Control Processor
The blower motor control processor controls the speed of the blower motor by increasing or decreasing the voltage drop on the ground side of the blower motor. The HVAC control module provides a voltage signal to the blower motor control processor over the blower motor speed control circuit. As the requested blower speed increases, the HVAC control module increases the amount of time that the speed signal is modulated to ground. As the requested blower speed decreases, the HVAC control module decreases the amount of time that the signal is modulated to ground.

HVAC Systems - Manual
Air Speed - Front Control
The blower motor forces outside air into the vehicle's interior. The vehicle operator determines the blower motor's speed when the driver places the blower switch in one of 5 blower speeds. The blower motor will always operate in any switch position other than OFF, as long as the ignition switch is in the RUN position. The blower motor and mode switches are located within the HVAC control module. The blower motor OFF input is connected in series with the HVAC control module by the off blower motor control circuit.
Depending upon the selected speed, power is provided to the blower motor from either the ignition 3 voltage or battery positive voltage circuits from the fuse block. The battery positive voltage circuit only provides power when the High blower switch position is selected. Power and ground are provided to the HVAC control module by the ignition 3 voltage and the ground circuits.
Low Blower Speed
When the Low 1 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the low blower motor control circuit. Voltage is divided between 4 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
Medium Blower Speeds
When the Medium 1 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 1 blower motor control circuit. Voltage is divided between 3 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
When the Medium 2 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 2 blower motor control circuit. Voltage is divided between 2 series resistors, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
When the Medium 3 blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the medium 3 blower motor control circuit. Voltage is divided between a series resistor, a blower relay, and the blower motor to achieve the desired blower speed. The blower motor is grounded through the ground circuit.
High Blower Speed
When the High blower speed is selected, the HVAC control module applies voltage to the blower motor resistor assembly through the high blower motor control circuit. The voltage energizes the blower relay, causing the blower motor to be connected directly to the battery positive voltage circuit. The blower motor and blower motor relay are grounded through the ground circuit.

HVAC Control Module
The HVAC control module is a class 2 device that interfaces between the operator and the HVAC system to maintain air temperature and distribution settings. The battery positive voltage circuit provides power that the control module uses for keep alive memory (KAM). If the battery positive voltage circuit loses power, all HVAC DTCs and settings will be erased from KAM. The body control module (BCM), which is the vehicle mode master, provides a device on signal. The control module supports the following features:

Feb 09, 2018 | 2005 Chevrolet Tahoe

1 Answer

Where is the blower motor and resistor located on a2006 trailblazer


{: ) The front blower motor is located beneath the right side of the Instrument Panel (dashboard), just behind the glovebox. The resistor is just on the near left, mounted on the HVAC casing. Just trace the wire from the blower motor and the other end will lead you to the resistor block.

Jun 14, 2011 | 2006 Chevrolet Trailblazer

1 Answer

Took out glove box can,t locate blower resister


Hi!!
The blower motor and fan are located in the lower right hand corner of the HVAC module. Remove the right closeout/panel insulator to access the blower. The blower motor resistor is the part where the electrical connector goes into. Here is a pic. of the blower motor assembly and the blower motor resistor.
1kbron_111.gif
BLOWER MOTOR RESISTOR 1kbron_85.jpg

Good Luck!1 A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Jan 04, 2011 | 2000 Oldsmobile Alero

1 Answer

I have a 2006 Dodge Ram diesel. Can you tell me where the resistor for the blower motor is located ?


It's right next to the blower, above the passenger's feet. See pic below.


jturcotte_37.jpg
  1. Disconnect and isolate the negative battery cable.
  2. Reach under the instrument panel near the blower motor and disconnect the wire harness connector from the blower motor resistor.
  3. Remove the two screws that secure the blower motor resistor to the HVAC housing.
  4. Remove the blower motor resistor from the HVAC housing.

Nov 30, 2010 | 2006 Dodge Ram 2500

1 Answer

2005 Jeep Grand Cherokee. Htr/AC fan switch only functions @ highest speed. At lower speed settings I can hear doors opening and closing---but not air.


replace the blower motor resistor. It controls the fan speeds. It defaults to high speed only when it fails.

How to replace the blower motor resistor block: Caution: Stay clear of the blower motor and resistor block (Hot). Do not operate the blower motor with the resistor block removed. 1. Disconnect and isolate the battery negative cable.
2. Remove the glove box from the instrument panel.
3. Pull out the lock on the blower motor resistor wire harness connector to unlock the connector latch.
4. Depress the latch on the blower motor resistor wire harness connector and disconnect the connector from the resistor.
5. Remove the two screws that secure the blower motor resistor block to the HVAC housing.
6. Remove the resistor block from the HVAC housing. Installation:
1. Position the blower motor resistor block into the HVAC housing.
2. Install the two screws that secure the resistor block to the HVAC housing. Tighten the screws to 2.2 Nm (20 in. lbs.)
3. Connect the wire harness connector to the resistor block.
4. Push in the lock on the blower motor resistor wire harness connecgtor to lock the connector latch.
5. Install the glove box.
6. Reconnect the battery negative cable.
7. Have a nice day!

Oct 11, 2010 | Jeep Cherokee Cars & Trucks

2 Answers

Where is the blower motor resister located on on a 2005 dodge dakota V6 slt?


It should be mounted on the blower box,near the blower motor to keep it cool,it mounts on the out side,but actually goes inside the blower box,it has a multi wire connector to it.

May 11, 2010 | 2005 Dodge Dakota

2 Answers

Liberty HVAC blower motor only works on hi speed. No low or middle speed. Is there a relay or thermal resistor for this and where is it located?


The HVAC Blower Motor Resistor needs to be replaced. It is located in behind the glove box. You have to remove the glove box which is easily done by releasing two clips located on each side of the compartment door. Then slide the cover to the right and the cover will come right off. I just had my replaced today and it only took the garage 10 minutes to install the new one.

Sep 03, 2009 | Jeep Liberty Cars & Trucks

1 Answer

Hvac blower motor not working


replace the "blower motor resistor" located next to the blower motor

Dec 22, 2008 | 1998 Ford Explorer

Not finding what you are looking for?
1999 Dodge Intrepid Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...