This is in a 2005 Dodge Dakota Quad cab 3.7. The drivers seat belt is buckled but the alarm and the light keeps flashing. Tried to disable it by following the manual but it does not disable. I think this may be the last Dodge we ever buy.Enough of the endless electrical issues. Our old 96 grand Caravan always had the ghosting wipers.etc. etc. Help please.
The Enhanced Warning System (BeltAlert) can be enabled
or disabled by your authorized dealer or by
following these steps:
NOTE: The following steps must occur within the first
60 seconds of the ignition switch being turned to the ON
or START position. DaimlerChrysler does not recommend
deactivating the Enhanced Warning System
(BeltAlert).
1. Turn the ignition switch to the OFF position and
buckle the driver's seat belt.
2. Start the engine and wait for the Seat Belt Warning
Light to turn off.
3. Within 60 seconds of starting the vehicle, unbuckle
and then re-buckle the driver's seat belt at least three
times within 10 seconds, ending with the seat belt
buckled.
NOTE: Watch for the Seat BeltWarning Light to turn on
while unbuckling and off while re-buckling the seat belt.
It may be necessary to retract the seat belt.
**this is kinda weird** (improvement)
4. turn the key *slowly* so that the power to
the radio goes off but the engine is running, you should now here a
CHIME and the parking brake indicator light will come on now also.
PAUSE. then turn the ignition off all the way, you should now here
another CHIME.
in MY '05 RAM it works like this, but in a newer built RAM or your Dakota it might not, good luck.
I have a 2004 Dodge Dakota and the seat belt light is driving me "Krazy". I've not found a fix for it yet so I have done what every loving father would and placed a photo of my children over it ! Problem solved. If you have a real way to fix this issue I would appreciate some advice.
The problem is in the switch.When you buckle up you close the seat belt switch. Replace it or bypass it.
×
I have a 2004 Dodge Ram 1500 Quad cab 4X4, 2.8L engine. Driver's seat belt alarm will not shut off until 10 min after we are on the road. Chime shuts off / light still on?
I've tried all the tricks mentioned above, with no success! Doesn't matter what I do can't get it to stop or turn off.
This vehicle only gets 13 mpg to boot?
I have a 2006 Dakota crew cab 4x4 SLT V8 ( piece of **** ) bought brand new, already had the tranny worked on twice because the tranny lights keeps coming on! Now as of new years 2011 my flashing lites when activatin the alarm stopped flashing! Now my seat belt chime will not stop ringing and my frickin seat belt is buckled! Also the seat belt lite is on, yet my belt is buckled. Can anyone help me or do I need to see the dealer for this???
I have the same problem..did you find a solution? Thanks
×
I'm having same problem. Gonna have to look for a broken wire I guess.
I just found a wire broke. its a green w/red stripe if u follow it from seatbelt plug to under the trim by door it connects with 2 purple w/ green or bluegreen striped wires they were hard and when i tugged on them they came appart so i got a piece of wire and connected them and now it works . u have to cut the tape its so fabric type tape. it was broke right beside the drivers seat under trim .
i just found a wire broke. its a green w/red stripe if u follow it from seatbelt plug to under the trim by door it connects with 2 purple w/ green or bluegreen striped wires they were hard and when i tugged on them they came appart so i got a piece of wire and connected them and now it works . u have to cut the tape its some fabric type tape. it was broke right beside the drivers seat under trim .
×
8,344 views
Usually answered in minutes!
×