Question about 2001 Suzuki Grand Vitara

2 Answers

Engine makes noise when i push down on the clutch

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Hmmm, main bearing noises are usually more obvious when the cluch is released, as the engine is driving the gearbox input shaft, it's more likely the clutch throwout bearing or the spigott bearing, does the noise start as soon as the slack is taken up in the pedal? if yes, it's most likely the throwout bearing, if the noise starts with the pedal about halfway its more likely the spigott bearing. either way, it's probably about time for a replacement cluch kit. Not sure about the 2001 model but 90's model Vitara's tend to suffer from gearbox input shaft wear at the spigott bearing...

Posted on Jul 10, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

May be worn main bearing

Posted on Jun 30, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

keemo68
  • 1263 Answers

SOURCE: truck makes loud noise unless clutch is pushed in

chances are the adjustment of the throwout bearing fork is the problem . because of vibration that is the rattling that you are hearing. correct adjustment should be as follows.

#1...peddle travle should be no more than 1 1/2 inches

#2...the clearance between throw out bearing and fork no more than 1/2 inch

#3...clearance between fork and fork stops is 1/8 inch

also there should be grease zerts in the shaft that holds the fork and linkage make sure they are not dry of grease...please rate the solution....thanks

Posted on Sep 22, 2008

emissionwiz
  • 75797 Answers

SOURCE: chirping noise when engine is started

the noise is from a worn out clutch pressure plate release bearing, replace it..

Posted on Dec 10, 2008

Eurodinno
  • 57 Answers

SOURCE: everytime i push my clutch pedal down the car

There is a problem with dirty injectors. Please clean those by putting high octane fuel in your car or putting an octane booster in your car also you may lube your cluch look for a valve itatake under the car for that.

Posted on Nov 30, 2009

  • 1 Answer

SOURCE: when clutch pushed in it makes high pitched squeel

Im a mechanic, i think you will find it will be the clutch release bearing on the clutch fork, when you push the clutch in it will push the fork which will push the clutch release bearing onto the clutch plate which rotating with the engine revs

Posted on Mar 23, 2009

  • 312 Answers

SOURCE: clutch makes whistle noise

Sounds like a throwout bearing is dry.

Posted on Jun 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Push down clutch makes grinding noise


cluch plate to be replaced, flaw in materail caused plate to shatter!

Oct 02, 2013 | Honda Civic Cars & Trucks

1 Answer

Metal on metal noise


hi,

most likely the throw out bearing is at fault. when you push the clutch a spinning bearing pushes the clutch plate away from the flywheel disengaging trans so you can switch gears. the transmission has to come away from the engine to fix it.

jm

Jul 04, 2017 | Toyota Corolla Cars & Trucks

1 Answer

93 Nissan altima, high pitched whirring noise upon starting the vehicle. Continues when clutch engaged and driving. Just replaced a part which when you press the clutch down it connects to a cylinder...


hi,,

sounds like you had your clutch slave replaced. also I see that you said it doesnt make noise when you push the clutch to the floor, so usually thats the throw out bearing, its inside the transmission. the transmission has to come apart from the engine. the check engine light could be either from the transmission getting a fault, or the oil inside the cap is causing an electrical issue. so you need a throw out bearing and a new distributor. stanzas good for a couple more trips and thats it.

Jul 25, 2017 | Cars & Trucks

1 Answer

I changed my clutch and releasing bearing but the noise is still there. When ever i release the clutch the noise starts like the release bearing problem and when i take off in first and second gear there...


a release bearing will make noise when you push on the clutch, the input shaft bearing will make noise when you release the clutch, the transmission will have to be removed and torn down to replace the bearing.

Apr 15, 2011 | 2004 Honda Civic

1 Answer

1995 chevy s10 2.2 when engine is running and you push clutch all the way down starter bendix is going out making terrible sound already replaced ingnition lock didn't help thanks


Pushing the clutch down shouldn't have anything to do with the starter. It sounds like your throwout bearing may be making the noise.

Dec 19, 2010 | 1995 Chevrolet S-10 CA Edition

2 Answers

What are the symtoms of a bad clutch switch


If the engine revs up more than normal and your not gaining speed then the clutch is slipping.If you shift down to pass and then try to accelerate and the engine revs up but you don't gain speed,the clutch is slipping.If with the park brake on you can let the clutch out without stalling you need a clutch.If it makes a tinny sound when the clutch is pushed,you need a trow-out bearing

Oct 26, 2009 | Ford Ranger Cars & Trucks

1 Answer

Car makes a metalic grinding noise when in neutral


You need a new throwout bearing in your clutch assembly.

Sep 10, 2009 | 1994 Pontiac Bonneville

2 Answers

NOISE WHEN LETTING OUT CLUTCH WHILE IN GEAR


Clutch plate springs brocken.Thats where your noise is comming from.The only solution is to change the clutch.Hope that was helpfull.

Jul 24, 2009 | 1993 Toyota 4Runner

1 Answer

When clutch pushed in it makes high pitched squeel


Im a mechanic, i think you will find it will be the clutch release bearing on the clutch fork, when you push the clutch in it will push the fork which will push the clutch release bearing onto the clutch plate which rotating with the engine revs

Mar 23, 2009 | 2000 Jeep Wrangler

Not finding what you are looking for?
2001 Suzuki Grand Vitara Logo

505 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...