Question about 2004 Ford Freestar

1 Answer

I need to know if the blower motor for the 2004 ford freestar hvac is the same front and rear or not.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

The blower will diferent from the front blower if that is what ur asking

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram showing location of blower motor and installation for 2004 cadallic sedan 8 cyl


. How do you know you need one ? Did you do electrical circuit testing ? Is your HVAC - heater / A/C system automatic or manual ? Could need a blower motor control processor ! Electronic module . Did you check the blower motor fuse ? HVAC /BLO fuse 40amp in the rear fuse block ? Under the back seat ?

Apr 18, 2017 | Cars & Trucks

1 Answer

2004 ford freestar front blower motor will not come on. Windshield wipers only work occasionally


Pull the control switch out of the dash and check the switch connector for burnt connectors terminals, it will be be discolored, if you do find the switch burnt replace the switch and buy a repair connector from Ford. If the connector is ok then replace the blower motor resistor near the blower motor, it can cause this problem as well, in fact do that first, the blower resistor module is only about $18.00 (Source Rockauto.com). the wipers are controlled through the BCM (body control module), it can be tested with a scan tool. Below is a picture of the blower resistor module.
resistor-cvwiva3pd4w10j2ma2c0he5w-1-0.jpg

Apr 03, 2017 | 2004 Ford Freestar

1 Answer

2004 Trailblazer ext rear a/c blower not working.


Do you know how to do automotive electrical testing ? How to read an use a wiring diagram ? Do you have manual or automatic climate control ? Automatic has a control processor (electronic )
You would need to take Rear Quarter Trim Panel off- Right Side (TrailBlazer, Envoy, Bravada) To get at the blower motor for testing electrical circuits . This video i have posted is for the front blower motor , you test the AUX . blower motor the same . Blower Motor Problems Auto Repair Help

Free wiring diagrams at
http://www.bbbind.com/free_tsb.html

HVAC Blower Motor Circuit Electric Testing Techniques You Need to Know


Mar 12, 2017 | Cars & Trucks

1 Answer

2004 f 150 4x4 blower motor works spuratically off and on after vehicle warms up


To know for sure what's wrong some electrical testing needs to be done ! Videos on youtube testing blower motor electrical circuit . Could be the blower motor itself , the resistor pack , a relay or a front blower motor speed controller . And all this depends on if yours has electronic manual or electronic automatic temp. control . http://www.bbbind.com/free_tsb.html free wiring diagrams . HVAC Blower Motor Circuit Blower Motor Problems Auto Repair Help

Jan 03, 2017 | Ford F-150 Cars & Trucks

1 Answer

Driver side blows hot air while passenger side blows cold air


You need to replace the driver side temperature blend door actuator , electric motor that controls the temp .The instrument panel may need to be pulled out to replace it . You may want to take it to a qualified repair shop . As far as the rear blower motor , the motor could be bad or the auxiliary blower relay module , or the blower motor relay could be the problem . Without knowing component position in the vehicle you have a difficult time tracking down these parts .

Jun 29, 2016 | 2004 Ford Freestar

2 Answers

How can i get rear a/c blower moter to come on


There is a relay that controls the motor. Have you checked it? The wiring diagram shows it is located in the "Bussed Electrical Center (BEC) 13-5". I'm not sure exactly where that is located, but it is probably under the hood, or the drivers side under the dash. I will check the manual to see if it shows where it is. When you say you have 12V, where did you measure that? If you are seeing 12V at the motor, and you have a good ground the motor has to run, or it's bad.

May 30, 2014 | 2004 Ford Freestar

1 Answer

04 yukon slt 2wd hvac rear blower motor won;t run. jumped motor its good.


There is a rear control module and a rear data processor for the blower motor and the blend doors.
Your probably going to need a shop manual to have the test procedures for those circuits.
One orange wire goes to the module from a 10amp fuse in the box in the engine compartment, the other orange wire goes to the module from a 30amp fuse in the same box. There is a third orange wire between the front HVAC control panel and the rear module.

Feb 02, 2013 | 2004 GMC Yukon

2 Answers

How do i get to the rear spark plugs & coil pack on my 2005 Freestar


the coil pack is in the front, but the back plugs can be done (not easily) by removing the 'shelf' over the top of the rear cowl and removing the wiper motor assembly. I hope this helps - rate my answer to let me know and to help others with the same problem

Feb 05, 2011 | 2004 Ford Freestar

1 Answer

Where is the blower motor... i know that is the problem, but where and how do I change it. i already have the part


Blower Motor Removal & Installation Front To Remove:
NOTE: The blower motor is positioned on the passenger side of the vehicle beneath the instrument panel, and can be removed from the vehicle without removing the HVAC housing.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Passenger side cowl trim panel
    • Carpet to access the front upper screw that secures the air inlet housing
    • Recirculation door actuator
    • Recirculation door actuator wire lead from the routing clip located on the lower air inlet housing and position the wire lead aside
    • Blower motor wire lead connector from the blower motor resistor or power module, depending on application. Lower Air Inlet Housing chr_pacific_lwr_inlt_hsng.gif

    • One screw (from the top) that secures the lower air inlet housing to the upper air inlet housing
    • Four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and remove the lower HVAC housing Blower Motor Wire Lead Grommet chr_pacific_blwr_wrg_grmmt.gif

  3. Feed the rubber blower motor wire lead grommet through the opening in the lower air inlet housing.
  4. Push the blower motor wire lead through the opening in the lower air inlet housing and remove the lower air inlet housing from the vehicle.
  5. Place the recirculation-air door as needed to access and remove the three screws that secure the blower motor to the lower half of the HVAC housing.
  6. Lightly bend the recirculation air door far enough down to remove the blower motor and wheel from the HVAC housing. Blower Motor Mounting Tabs blwr_mnting_tabs.gif

  7. Remove the blower motor and wheel from the HVAC housing. Make a note of the location of the blower motor mounting tabs.
To Install:
  1. Install or connect the following:
    • Blower motor and wheel to the lower half of the HVAC housing and line up the blower motor mounting tabs to the correct location on the HVAC housing
    • Blower motor and wheel into the HVAC housing by lightly bending the recirculation-air door far enough down
    • Three screws that secure the blower motor to the HVAC housing by positioning the recirculation-air door as needed
      1. Torque to: 17 inch lbs. (2 Nm)
    • Blower motor wire lead through the opening in the lower air inlet housing and seat the rubber grommet into the lower air inlet housing
    • Recirculation-air door pivot into the lower air inlet housing
    • Four screws (from the bottom) that secure the lower air inlet housing to the upper air inlet housing and the lower HVAC housing
      1. Torque to: 17 inch lbs. (2 Nm)
    • One screw (from the top) that secures the lower air inlet housing to the upper air inlet housing
      1. Torque to: 17 inch lbs. (2 Nm)
    • Blower motor wire lead connector to the blower motor resistor or power module, depending on application
    • Recirculation door actuator wire lead into the routing clip located on the lower air inlet housing
    • Recirculation door actuator
    • Carpet
    • Passenger side cowl trim panel
    • Negative battery cable
  2. Perform the heater-A/C control calibration procedure.
Rear To Remove:
NOTE: The rear blower motor and blower wheels are repaired only as a balanced unit. The entire blower motor and wheel assembly must be replaced if either component is fault or damaged.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Front center floor console cover
    • Negative battery cable Rear Blower Motor Housing chr_pacific_rear_blwr_hsng.gif

    • Body wire harness connectors from the rear blower motor power module and the rear mode door actuator
    • Body wire harness bracket from the console support bracket
    • Eight screws and the two console support brackets from the floor console base and duct assembly
    • Four screws that secure the rear blower motor housing to the floor console base and duct assembly
    • Rear blower motor housing and place it on a bench
    • Rear blower motor wire harness connector from the power module
    • Eleven retaining clips and three screws that secure the housing together
    • Two halves of the housing
    • Blower motor wire harness and grommet from the housing and remove the blower motor
To Install:
  1. Install or connect the following:
    • Rear blower motor into the housing and install the blower motor wire harness and grommet
    • Two halves of the rear blower motor housing and install the eleven retaining clips and three screws
      1. Torque to: 17 inch lbs. (2 Nm)
    • Rear blower motor wire harness connector to the rear blower motor power module
    • Rear blower motor housing into the floor console
    • Four screws that secure the rear blower motor housing to the floor console base
      1. Torque to: 17 inch lbs. (2 Nm)
      2. Two console support brackets onto the floor console base
      3. Eight screws that secure the support brackets to the floor console base
        1. Torque to: 17 inch lbs. (2 Nm)
      4. Body wire harness bracket onto the console rear support bracket
      5. Body wire harness connectors to the rear blower motor power module and the rear mode door actuator
      6. Negative battery cable
      7. Front center floor console
  2. Calibrate the A/C-heater control.
prev.gif next.gif

Aug 13, 2010 | 2004 Chrysler Pacifica

Not finding what you are looking for?
2004 Ford Freestar Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...