How to Install glove box mg td

Is ignitor lighting sounds like one click is gas valve

Ajust idle mix and idle speed..get details from library..partstore..etc

check earths chassis to engine or use a jump lead to a goob earth on body from battery

This something I copied from an eBay listing, so I haven't done it yet.

Uplander Glove Box Hinge

Used in good condition.

Has minor cosmetic flaws like scratches, scrapes or scuffs you would normally expect to find on a used item.

Includes 5 screws and nuts to replace the rivets.

A web search may yield a video for you to watch.

Required Tools:

Flat screwdriver

Phillips screwdriver or else a 7mm socket and rachet

Electric drill with a 3/16" inch bit

Needle nose pliers or vise grips.

3/8" inch wrench.

Removal Instructions:

Remove the panel underneath the glove box.

3 Black 3/4" inch pan head bolts hold it in place.

Use a flat screwdriver to pry a little and slip the prongs of a pair needle nose pliers on either side of a bolt.

Push down on the handle of the needle nose pliers to remove each bolt.

Remove 2 phillips screws along the bottom of the glove box hinge.

Remove 2 phillips screws inside the glove box.

Remove the small black cabin air filter access door inside the glove box.

Put your fingers inside the left side of the access door opening.

Yank backward to loosen the 1 retainer clip on the left side of the glove box assembly.

Often times the 2 retainer clips on the right are also loosened.

Skip steps 1 to 5 if you can remove the entire glove box assembly at this point.

1) Open the front passenger door.

2) Use the flat screwdriver to remove the fuse access panel.

3) 3 Retainer clips hold it in place.

4) Use both hands to grab the glove box assembly on the far right.

5) Yank backward to loosen the 2 retainer clips on the right side of the glove box assembly.

Pull the entire glove box assembly out of the dashboard.

Some models have a strip of masking tape behind the glove box to hold it in place.

Some models have a lamp inside the glove box. Leave it in place or else pry a black tab to disconnect the wiring harness.

Hold the 'ears' of a rivet with the vise grips or needle nose pliers.

Drill through the 5 rivets with your electric drill and 3/16" inch bit.

The rivets may fall apart. Otherwise, twist the vise grips or pliers for removal.

Remove 4+2=6 phillips screws on the glove box door.

Use a flat screwdriver to pry 2 tabs on the glove box door to remove the rectangular portion.

Installation Instructions:

Install the 4+2=6 phillips screws on the glove box door.

Install the 5 replacement phillips screws and nuts where the rivets were.

For some models reconnect the glove box lamp wiring harness.

Align the 3 retainer clips and push the fuse access panel into place.

Align the 3 retainer clips and push the glove box assembly firmly into place.

Install the small black cabin air filter access door inside the glove box.

Install 2 phillips screws inside the glove box.

Install 2 phillips screws along the bottom of the glove box hinge.

Install 3 black 3/4" inch pan head bolts under the glove box assembly to hold the panel in place.

- Done -

If you mean the climate control blower motor, it's usually under the dash on the passenger side on Hondas.

1990-93 Accord

1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
2. Remove the glove box.
3. Remove the glove box frame (lower support) Fig. 2: Remove the glove box and frame
   
   
4. If not equipped with air conditioning:
   1. Remove the three screws and remove the heater duct.
   2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
5. If equipped with air conditioning:
   1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
   2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
   3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
   4. Remove the retaining nuts and remove the blower assembly. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully
      Fig. 4: Remove the lower covers from the blower unit
      To install:
      
6. Install the blower unit and tighten the retaining nuts.
7. On air conditioned vehicles:
   1. Install the lower covers and the retaining band.
   2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
   3. Install the kick panel and reposition the carpet.
8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
10. If applicable, enable the SRS.
11. Connect the negative battery cable.

1988-91 Prelude

1. Disconnect the negative battery cable.
2. Remove the glove box and frame (lower support).
3. Remove the 4 screws and remove the heater duct. Fig. 5: The glove box and frame are secured by several small screws
   
   
4. Remove the 3 mounting bolts.
5. Unplug the wiring connectors from the blower motor, resistor and recirculation controller. Remove the blower motor assembly.
6. Reinstall in reverse order. Make certain the blower mating surfaces are tightly sealed.

open the glove box door, remove everything from inside the glove box. remove the clip retaining the door-stop strap. pivot the glove box downward,unsnap the hinges from the instrument panel and remove the glove box. install in the reverse manner.

990-93 Accord
See Figures 2, 3 and 4

1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
2. Remove the glove box.
3. Remove the glove box frame (lower support)
4. If not equipped with air conditioning:
5. If equipped with air conditioning:To install:
   
6. Install the blower unit and tighten the retaining nuts.
7. On air conditioned vehicles:
   1. Install the lower covers and the retaining band.
   2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
   3. Install the kick panel and reposition the carpet.
   
   
8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
10. If applicable, enable the SRS.
11. Connect the negative battery cable.
12. 
    

Remove all of the contents in the glove box. Remove the glove box door support. Open the glove box. Squeeze the sides of the glove box inward, to drop the box door open further. The cabin air filter is in a small rectangular box, behind the glove box.

Remove the glove box.
Cut the plastic cross brace in the glove box opening with diagonal cutters in the area shown, and discard it.
Remove the bolts, the screws and the glove box frame.

1. Remove the filter lid (A) from the evaporator, then pull out the dust and pollen filter (B).
2. Install the filter in the reverse order of removal. Make sure that there is no air leaking out of the evaporator.
3. Install the glove box frame and glove box in the reverse order of removal.