Subaru forester 98 need oil pan bolt torque specification

12-13 foot pounds

Pontiac Engine Torque Specs

Butler Performance https://butlerperformance.com > p-34888-pontiac-engi...
Pontiac Engine Torque Specs ; Oil Pump Cover Bolts, Engine Oil, 15 ft-lbs. ; Windage Tray, Engine Oil, 15 ft-lbs. ; Oil Pan, Engine Oil, 12 ft-lbs. ; Camshaft ...

Oil and Transmission Pan Bolts. How much torque?

GMForum.com https://www.gmforum.com > ... > 1992-1999
Jun 12, 2003 - the Torque Specifications for the Xmission Oil Pan Bolts are 12-13 Ft. Lbs. Works for me.

Transmission pan Torque spec
Apr 28, 2017
4T65E-HD transmission pan bolt torque values
Feb 8, 2008
More results from www.gmforum.com

2004 Pontiac Sunfire 2-dr Transmission Pan Gasket ...

MyCarSpecs https://www.mycarspecs.com > pontiac > sunfire > 2004
The transmission pan gasket helps to seal in transmission fluid and keep it from leaking everywhere. This will degrade over time and need replacement, ...

..

Yes, all oil pans need gaskets. The torque is 18 ft lbs. PDF file

Oil Pan Replacement - ChevroletForum

https://chevroletforum.com > forum > equinox-23
PDF
2005 Chevrolet EQUINOX. Submodel: LT ' Engine Type: V6 ' Liters: 3.4. Fuel Delivery: FI ' Fuel: GAS. Oil Pan Replacement. Tools Required. J 39505 Torque ...


Do you need to torque oil pan bolts?
Engine oil pan bolts range in torque from seven foot-pounds to 22 ft-lb or more for large engines with heavier pans and bolts. Once you've torqued the bolts and filled the engine with oil, you should run the engine for five minutes to bring it up to normal operating temperature.

Videos and more info

https://www.google.com/search?q=2012+chevy+equinox+oil+pan+bolts+torque

..

Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

oil pan bolts are torqued in inch lbs due to their size and usually doesn't require a specific torque value. all bolts in a manual does show torque settings in all applications.However because of its non critical application a specific value is not necessary. a "snug" tightness is adequate with proper gasket/sealer in place to prevent seepage or leaks. in that area of the engine,leak can come from almost anywhere. top,front,or even rear of the engine blown by the wind a car creates while in motion. oil sensors{ but not limited to} are notorious for leaks as the vehicle ages particularly in that area. steam clean or thoroughly degrease the area and run the engine a few miles and recheck the area before proceeding to make repairs.

with cast aluminum oil pan 8 -10 ft lbs sheet metal pan 70-90 INCH lbs

Oil pan on the engine block. Torque the bolts EVENLY to 9 ft. lbs. (12 Nm) working from the center to the end position on the oil pan.

Fig. Oil pan bolt torque sequence-3.0L engine

Hope this helps (remember to rate and comment this answer).

Torque the oil pan bolts 36 to 40 in-lbs. starting from the center and working your way to the ends.

Using a small 1/4" socket set and just your thumb and one finger with no leverage on the handle to tighten bolts. (kinda like chocking up on a bat if you know what I mean.) Starting in the middle go from one side to the opposite working your way to the corners. Use some "Permatex #2" to hold gasket in place and to help seal. Make sure not to over tighten bolts...it can actually cause it to leak.

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

MY 98 SUBARU FORESTER AT LIGHT IS BLINKING AND SOMETIMES STALLS WHEN STOPPING AT A RED LIGHT