How to remove wiper blades

Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

Two ways... Easiest is to go to a parts shop that has a sign, "windshield wipers replaced free"...
They are pretty easy to unclip. Just the end with the blades comes off for replacement. New blades have instructions in the package.

Amazon.com: Silhouette Replacement Blade

www.amazon.com > ... > Replacement Blades
Amazon.com, Inc.This replacement blade is compatible with all Silhouette electronic cutting tools. .... center" from Silhouette online store) It has taken me 3 blades to get through ...
Windshield Wiper Blades - Advance Auto Partsshop.advanceautoparts.com/c3/windshield-wiper-blades/15566462 results - Save on Windshield Wiper Blades with great deals at Advance Auto Parts. Buy online, pick up in-store in 30 minutes. ... Replacement Parts (460).Wiper Blade (Windshield) at AutoZone.com - Best Wiper ...www.autozone.com/ignition-tune.../wiper-blade-windshieldAutoZoneReplacement Parts ... Vehicle Specific Bosch Evolution/Wiper Blade (Windshield).Price: $15.19. Part Number: 4820; Application: Front; Notes: Beam Design

On the WEB:

Front Wiper Blade Change Jaguar XJ8 (2004-2009) - 2008 ...

www.carcarekiosk.com/...Jaguar.../windshield_wiper_blade.../replace_wi...
Free video on how to replace the front windshield wiper blades in a 2008 Jaguar XJ8 L 4.2L V8. Complete instructions for changing the front wiper windshield ...

Hi there,

• Turn the ignition on, and turn the front windshield wipers on. When the wipers are facing straight up on the window, turn the ignition off so they remain in that position.
• Disconnect the negative battery cable with an adjustable wrench. Remove the passenger side wiper blade assembly, by removing the pivot nut at the bottom with an adjustable wrench. Remove the wiper linkage access cover, and use a screwdriver to remove the wiper motor clip. Remove the wiper linkage from the wiper motor.
• Disconnect the electrical connector on the wiper motor. Remove the bolts and nuts, securing the wiper motor with a socket wrench. Remove the wiper motor from the vehicle. Install the new wiper motor, and tighten mounting bolts and nuts with a socket wrench. Connect the electrical harness to the new wiper motor. Connect the wiper linkage, and insert the linkage clip. Install the wiper blade assembly, and tighten the nut with an adjustable wrench.
• Connect the negative battery cable securely, using an adjustable wrench.

Hope this helps...

Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:

1. Turn ignition switch to ACCY position.
2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.

To Install:

1. Insert wiper arm hook through opening in wiper blade.
2. Place wiper blade pivot in the inside radius of wiper arm hook.
3. Pull on wiper blade pivot into hook until it locks into place.
4. Check wipers for proper operation.

Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.

1. Remove washer hose.
2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
3. Remove wiper arm from shaft.

To Install:

1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
2. Press arm assembly on shaft and push retaining latch IN.
3. Connect washer hose.
4. Remove windshield markings and check wipers for proper operation.

why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.

1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.

1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.

1. Remove left windshield wiper adapter and connecting arm clip access cover.

1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
   

----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal

1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.

1. Disconnect battery and wiper motor electrical connector.

1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .

1. Disconnect the battery ground cable (14301).

1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .

1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.

1. Reach through the access cover opening and unsnap the wiper motor clip.

1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.

1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.

1. Remove nut and ground strap.

1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .

Installation

1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).

1. Install nut and ground strap.

1. Connect wiper motor electrical connector.

1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.

1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.

1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.

1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
   

1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.

1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.

1. Test the system.

How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:

• Flat blade screwdriver (small)
• Small nosed pliers
• Latex or vinyl gloves
• Safety goggles

To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.

• Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
• Step 2: Locate the mounting clips at the top pivot on the wiper blade
• Step 3: Release the clip and remove the wiper arm
• Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
• Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:

• Make sure the wiper blades are the same size as the original blades.
• When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
• Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
• Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

According to the Haynes repair manual Chapter 12:

1. Disconnect the negative battery cable
2. Detach washer hoses, lift the wiper arm covers and mark the wiper arm locations on the pivot shaft for later re-installation. Remove the wiper pivot nut and remove the wiper arms.
3. Remove the cowl cover (from chapter 11)
3a. Remove the wiper arms then remove the screws that hold the lower area of the cowl cover to the wiper module.
3b. Disengage the quarter turn fasteners that hold the outer ends of the cowl cover to the wiper module.
3c. Open the hood and release the wing nuts that hold the front of the cowl cover to the wiper module.
3d. Close the hood but do not latch it. Now remove the outboard screws and lift the cover up enough to get to the washer hose.
3e. Disconnect the washer hose from the right washer nozzle. Close the hood but do not latch it. Lift the cowl cover toward the windshield and off the vehicle.
3f. Installation is the reverse of removal
4.Open the hood. Disconnect the wiper motor electrical connector.
5. Disconnect the windshield washer hose from the coupling inside the unit. Disconnect the drain tubes from the bottom of the wiper unit.
6. Remove the wiper unit mounting bolts. (Picture appears to be three (possibly allen head) bolts)
7. Remove wiper unit.
8. Installation is the reverse of removal. Wiper blade and wiper arm adjustment is measured with the wipers parked; correct adjustment is the lower wiper arm approximately 1.5 inches distance from the cowl cover and the upper arm approximately 2.5 inches from the lower arm. Operate the wiper motor and check that the wiper motor parks when the wiper switch is OFF.

please rate as fixya if this is what you need. Mounting Arm and Pivot Shaft —Windshield Wiper Removal
NOTE: The windshield wiper pivot arms (17526) must be in the highest position to remove them.

1. Turn the ignition switch (11572) to the on position.

1. Turn the windshield wiper (17500) on.

1. Stop the windshield wiper pivot arms at the highest position by turning the ignition switch off.

1. Remove the windshield wiper pivot arm.
   1. Remove the pivot arm nut cover.
   1. Remove the nut.
   1. Remove the windshield wiper pivot arm.

1. Raise and support the hood (16612).

1. Remove the cowl grille seal.

NOTE: The two cowl grilles overlap at the center. The LH cowl grille must be removed first.

1. Remove the LH cowl grille.
   1. Remove the screw cover.
   1. Remove the screws.
   1. Remove the clips.
   1. Remove the pin-type retainer.
   1. Remove the LH cowl grille.

1. Remove the RH cowl grille.
   1. Remove the screw cover.
   1. Remove the screws.
   1. Remove the clips.
   1. Remove the pin-type retainer.
   1. Remove the RH cowl grille.

1. Remove the mounting arm and pivot shaft.
   1. Disconnect the electrical connector.
   1. Remove the bolts.
   1. Remove the mounting arm and pivot shaft.