Question about 1999 Jeep Cherokee

1 Answer

Reset the message on panel

Now that I have had the repairs completed..Not able to reset the performance service message

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,392 Answers

Should be able to reset it through the overhead console if it is for the engine oil. If it is for something else, and the light is still on, it is not fixed.

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does " service brake booster" light always on??


SERVICE BRAKE BOOSTER
Refer to Brake Warning System Description and Operation in Hydraulic Brakes

SERVICE BRAKE BOOSTER
The SERVICE BRAKE BOOSTER message will be displayed when the supplemental brake assist signal circuit is toggled at 1.0 Hz with a 50 percent duty cycle. This message is also displayed if the instrument panel cluster (IPC) does not see an alive and well signal at key on. When this message is displayed it indicates a problem with the SBA and should be serviced or replaced.

How do the power brakes work ? Good .?

Service Brake Booster Message Displayed
Step
Action
Yes
No
Schematic Reference: Brake Warning System Schematics
1
Did you review the Brake Warning System Description and Operation and the Brake Assist System Description and Operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Hydraulic Brakes
2
Start the vehicle.
Is the REDUCED BRAKE POWER message displayed for 1 minute before the SERVICE BRAKE BOOSTER message is displayed?
YES - Go to Step 3
NO - Go to Step 4
3
Perform the Brake Assist System Diagnosis
Did you find and correct the condition?
YES - Go to Step 12
NO - Go to Step 11
4
Disconnect the Supplemental Brake Assist connector.
Test the ignition 1 circuit for an open or a short to ground.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 12
NO - Go to Step 5
5
Test both ground circuits for opens.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 12
NO - Go to Step 6
6
Test the engine on signal circuit for an open or a short to ground.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 12
NO - Go to Step 7
7
Test the vehicle speed signal circuit for an open.
Did you find and correct the condittion?
YES - Go to Step 12
NO - Go to Step 8
8
Test the supplemental brake assist signal circuit for an open or a short to voltage.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 12
NO - Go to Step 9
9
Connect the supplement brake assist connector.
Disconnect the instrument panel cluster connector.
Connect a DMM from battery positive voltage to the supplemental brake assist signal circuit.
Turn the ignition to the RUN position while observing the DMM.
Did the DMM flash battery voltage?
YES - Go to Step 11
NO - Go to Step 10
10
Replace the Supplemental Brake Assist pump motor assembly Refer to Power Brake Booster Auxiliary Pump Replacement .
Did you complete the replacement?
YES - Go to Step 12
--
11
Replace the instrument panel cluster. Refer to Instrument Cluster Replacement in Instrument Panel, Gages and Console.
Did you complete the replacement?
YES - Go to Step 12
--
12
Start the engine.
Does the Service Brake Booster message stay on?
Go to Step 2
System OK

Dec 25, 2016 | Cars & Trucks

2 Answers

What tools are needed to replace BCM?


Important: Perform new BCM setup when you replace Body Control Module (BCM). Refer to Body Control Module (BCM) Programming/RPO Configuration .
Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
Remove the left instrument panel insulator. Refer to Instrument Panel Insulator Replacement in Instrument Panel, Gauges and Console.
Disconnect the BCM electrical connectors.
Push the BCM up and move the bottom of the BCM away from and out of the mounting bracket slot in order to remove the BCM.
During Body Control Module (BCM) related service, the procedures below are designated to set-up the BCM correctly. Before you start, read these procedures carefully and completely.

Setup New Body Control Module (BCM)
Tools Required
Scan Tool (Tech 2) GM factory scan tool !
Important:
• Read this procedure carefully and completely.
• The BCM will not function properly if the Setup New BCM procedure is not performed.
• Perform the Theft Deterrent Re-learn procedure after successfully finishing the Setup New BCM procedure. If the Theft Deterrent Re-learn procedure is not performed after a BCM replacement, the following conditions may occur:
- The vehicle will not be protected against theft by the PASSLOCK system.
- The engine will not crank nor start. Your best bet is to take your vehicle to a dealer or a ASE certified repair shop who has proper tools .

Feb 16, 2016 | 2000 Oldsmobile Intrigue

1 Answer

What causes obd code u110c


U110C-NO FUEL LEVEL BUS MESSAGE
When Monitored and Set Condition:
U110C-NO FUEL LEVEL BUS MESSAGE
When Monitored: Ignition on.
Set Condition: No fuel level BUS messages received by the PCM for 20 seconds.
POSSIBLE CAUSES
DTC RESET
COMMUNICATE WITH BCM
FUEL LEVEL BUS MESSAGE
PCI BUS CIRCUIT OPEN FROM PCM TO BCM
BCM
TEST ACTION APPLICABILITY
1 NOTE: If a fuel level circuit or performance DTC is set along with P1681,
diagnose the circuit/performance DTC before continuing.
Turn the ignition on.
With the DRBIIIt, erase DTCs.
Start the engine on and off several times. Leave the engine running for at least 20
second each time.
With the DRBIIIt, read DTCs.
Does the DTC reset?
All
Yes ! Go To 2
No ! Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
2 Ignition on, engine not running.
With the DRBIIIt, attempt to communicate with the BCM.
Can communication be established with the BCM?
All
Yes ! Go To 3
No ! Refer to the Communication Category and perform the appropriate
symptom related to no communication with BCM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
3 Turn the ignition on.
Using the DRBIIIt, read the Fuel Level parameter in the PCM.
Does the DRBIIIt display a fuel level value?
All
Yes ! Replace and program the Powertrain Control Module in accordance
with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
No ! Go To 4
287
DRIVEABILITY - NGC
TEST ACTION APPLICABILITY
4 Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the BCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMINALS
RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the PCI Bus circuit from the BCM harness connector to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes ! Replace BCM in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
No ! Repair the PCI Bus circuit between the PCM and the BCM for an
open.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC
__________________

Jan 13, 2013 | 2006 Dodge Caravan

1 Answer

How to turn of change engine oil light on 2011 ford focus


From FocusFanatics online - -

Resetting the oil life monitoring system
1. Turn the ignition key to the on position. Do not start the engine.
For vehicles with push-button start, press and hold the START/STOP
button for two seconds without pressing the brake pedal. Do not attempt
to start the engine.
2. Press both the accelerator and brake pedals at the same time.
3. Keep both pedals fully pressed.
4. After three seconds, the Service: Oil reset in prog. message will be
displayed.
5. After 25 seconds, the Service: Oil reset complete message will be
displayed.
6. Release both the accelerator and brake pedals.
7. The Service: Oil reset complete message will no longer be
displayed.
8. Rotate the key to the off position.
For vehicles with push-button start, press the START/STOP button to
turn the vehicle off completely.

Jul 07, 2012 | Ford Cars & Trucks

1 Answer

On my 2000 jeep grand cherokee information center is displaying perform service i would like to know what i have to do to fix it


The perform service message tells you when you need to change oil. To reset it turn the key on and press the step button until miles to service is displayed (it should say 0 underneath). Then press and hold the reset button until it changes from 0 to 3,000 miles. Then start the vehicle. The message should no longer be displayed.

May 27, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

What does it mean when the message center says perform service? What kind of service?


"perform service" have your mechanic reset it for the amount of mileage you would like to perform your next service...such as an oil chg in 3000 miles...

Aug 06, 2010 | 2002 Jeep Grand Cherokee

2 Answers

Perform service jeep grand cherokee 2005 this message is appearing in the message center


Actually the newer cherokees are a little more complicated, it's not a reminder for an oil change. It is for an emssions service that should be performed according to the dealer. Here is the rest procedure

Turn ignition to on position, but do not start.
Depress brake pedal fully twice.
depress excellerator very slowly twice
Turn ignition off & that will reset the perform service indicator.
I am mechanic & we are getting frustrated because the dealers do not want to release this info to anyone, they want your money! Can you believe if you did not get them to perform the service they charge you a 1 hour shop rate??

Feb 10, 2010 | 2005 Jeep Grand Cherokee

1 Answer

EVIC - PERFORM SERVICE MESSAGE


To reset the perform service message , is as follows , turn ignition switch to the ON position , depress and release MENU push button until SERVICE INTV . = is displayed , press and release STEP button to step through available options. the last selected distance option displayed becomes the service interval at which the PERFORM SERVICE message will be displayed . if a new distance interval is selected , RESET SERVICE DISTANCE ? with a yes or no option. when yes is selected the accumulated distance since the last previous PERFORM SERVICE message will be set to zero because the service interval has been changed . when NO is selected , the distance until the next PERFORM SERVICE message is reduced by the accumulated distance since the last previous message . EVIC exits programming mode and returns to its normal operation mode when the C/T button is depressed or when the end of the programmable feature menu list is reached , whichever comes first .

Thanks for asking .

Dec 30, 2008 | 2002 Jeep Grand Cherokee

1 Answer

Wrench Light on the head Panel lights above the mirror.


Service intervals, service due.
Illuminates to indicate that routine
service should be performed. Check
your maintenance schedule to
determine the routine service to be
completed.
To reset the light, hold the SELECT
and UNITS controls on the trip
computer for five seconds. The light
will be illuminated and then extinguish after approximately four seconds.

Dec 15, 2008 | 2002 Mercury Cougar

2 Answers

Service message on 1995 Jeep Grand Cheerokee


It is the perform service indicator that is telling you it is time for service.
If you do not want to have car serviced right now, just just hit the reset button. You can also go thru the menu and set the mileage you want the Perform Service warning to come on.

Aug 27, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...