Question about 1987 Chevrolet Camaro

1 Answer

I have an 84 camaro that was just fine this morning. when i went outside this afternoon and tried to put it in gear it did'nt go. what could be the problem?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 54 Answers


Posted on Jun 30, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ford windstar wont go into gear intermitten

When batteries die the CPU program has a tendency to become corrupted . The normal method to reset it is to use a code reader but some times switching on and off and back on may re-set some parts of the program. Run the fault codes to see if you have any faults recorded as a check

Feb 09, 2014 | Cars & Trucks

1 Answer

2000 gmc safari parked in the rain won't start

Did you take the distributor cap off and see if it has moisture inside ?

Apr 14, 2013 | 2000 GMC Safari

1 Answer

Pulled in driveway this morning transmission was working fine. Went to pull out this afternoon, and transmission will not engage in any gear.

check fluid levels in transmission it needs to be tested to determine if its a sensor or something more most transmission shops will tell you what it is at a fair price find one that is trust worthy and has experience in transmissions

Feb 23, 2011 | Honda Accord Cars & Trucks

2 Answers

My 1999 yukon wont start i changed master air flow

Fuel pumps are real common to go out on those vehicles

Mar 15, 2010 | 1999 GMC Yukon

1 Answer

Lastnight my family and I went fro a drive all was

Sounds like your alternator is bad and drained your battery. Try recharging your battery and putting a new alternator on it.

Sep 23, 2009 | 1999 Ford Expedition

3 Answers

700 r4 shift hard

The u-joints could cause the banging when you put it in gear. You might want to check the kick down cable. If it's out of ajustment it can cause the hard shift. The transmission thinks the motor is going faster then what it is and will shift harder. Put the car up on jack stand in the rear and put the tranny in neutral.turn the drive shaft back and forth with your hand and see if you hear the clunk or bang you heard when you put it in gear. if not then I would go with the kick down cable being to tightor to short on ajustment. However you want to look at it.

Jul 25, 2009 | 1984 Chevrolet Camaro

1 Answer

Transmission will not change gears.

Transmission computer or no fluid or it needs a new transmission. Sry but you give limited info.

Jun 23, 2009 | 1996 Chevrolet Camaro

1 Answer

84 camaro turbo kit

Before you put a turbo on your going to want to replace your head seals,piston, etc... If youve already done this i would direct you to they will be able to help ou, there is most likely already a thread about this question. ( this is much to involved to answer here)

Sep 20, 2008 | 1984 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides