Question about 1995 Chevrolet Lumina

3 Answers

How do I replace the bulb for the brake light..I have the bulb, but just need to know what to do to replace it.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

R
Inside the trunk you will have access to your light assembly. Remove screws holding assembly. Screws may have rubber caps over them to protect. Wiggle and pull assembly into trunk. You should unclip wire connector if it is in your way. Have someone Tap your brake peddle to make sure your replacing correct bulb by looking at your working light on others side. Grab bulb with thumb and forefinger pull firmly without bursting the bulb with your fingers if you are one with strong fingers.

Bottlenose

Posted on Jun 29, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,007 Answers

Open your trunk. The bulb is accessed from the back of the tailight. turn the socket holder counter clockwise, pull it out, and remove and replace the bulb.

Posted on Jun 29, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,050 Answers

If it's one of the lower ones... go in through the trunk, look to see if carpeting or a cover needs to be removed, or peeled back, usually the sockets twists (turns) to be removed, then the bulb will be exposed. An 1157 bulb needs to be pushed in slightly and turned to remove, (Counter clockwise) A 3157 bulb pulles straight out. Also note that some vehicles still need the exterior lens to be taken off, but I do believe yours is sealed!

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Brake Lights Dull or Flickering - All Cars



Dull or Dim Brake Light Repair: If your car has a dull or dim brake light it is dangerous to you and other drivers. A dim brake light is a mystery to most people because the bulb is working, just not correctly. First confirm a new and correct brake light bulb has been installed. Next, turn the ignition key to the "on" position and have a helper depress the brake pedal. With the bulb installed touch a grounded test light to the outer bulb holder ring. If the bulb brightness changes the bulb socket ground has high resistance and needs to be repaired or replaced.

Flickering Brake Light Bulb Repair: A flickering brake light bulb can be very distracting and annoying. A brake light flickers because the power or ground is being obstructed momentarily. The most common cause for this condition is a loose fitting bulb socket. To check for this condition remove the brake light bulb in question, while a helper hold their foot on the brake pedal move the bulb around slightly in the socket. If the bulb flickers replace or repair the bulb socket as needed to regain proper brake light bulb operation. If the brake light bulb socket tests ok wiggle the brake light fuse and wiring at the brake light bulb socket, brake light switch and turn signal switch (American cars). If the brake light bulb flickers repair the component or wiring as needed.
Preferred Procedure: Always replace brake light bulbs with manufacturers recommend replacement bulbs. If you cannot find the correct replacement bulb part number consult an auto parts store for additional manufacturer information.
Common Problems
When brake light bulbs are replaced with the incorrect bulb causing no or dim brake light operation
If the brake lights stay on continuously it could mean the brake light switch has failed or an adjustment is needed.

on Dec 18, 2009 | Honda Civic Cars & Trucks

Tip

Both Lower Brake Lights Not Working


Check Brake Light Bulbs: All cars have three brake light bulbs that create the brake light illumination affect. If the lower two bulbs fail no lower brake light operation will occur. I know what you're thinking, you might say two brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove either of the brake light bulbs to confirm the bulb is ok or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are ok continue to the next step.

Checking the Turn Signal Switch: Most American cars are designed to have the brake light switch wiring intergraded into the turn signal switch. Because the brake light bulb and the turn signal bulb are one and the same the turn signal switch interrupts the brake light circuit and installs the blinker signal circuit when the turn signal switch is activated. If this switch fails it will not allow the brake light signal through to the brake light wiring. To test for this condition a car repair manual is needed to test incoming and outgoing electrical current. If brake light switch power is present at the turn signal switch but not at any outgoing brake light wires the turn signal switch has probably failed.

on Dec 18, 2009 | Honda Civic Cars & Trucks

2 Answers

Need to know which fuse control my brake lights. Light bulbs are fine but when i press the brakes the lights dont come on.


change the brake light fuses on ur chrysler 300. also get it checked at a dealer to spot any other issue, if any.

Dec 22, 2010 | 2008 Chrysler Aspen

1 Answer

I need to know which fuse needs to be replaced to make the driver's side brake light work? What a pain this always is. Who's idea was it to NOT include a fuse map for the interior of this car? Good Lord.


There is no separate fuse for one brake light,check the connector at the brake light bulb,and replace the bulbs,do not change the bulb out with a similar number,like if it uses a 3057 bulb,do not use a 3157,they are different.Look at the terminals,with no voltage to the light,and bend the contacts for the bulb inward to make sure there is contact.

Jun 01, 2010 | 2004 Dodge Durango

Tip

Check Brake Light Bulbs: All cars have three brake light bulbs that create the...


Check Brake Light Bulbs: All cars have three brake light bulbs that create the brake light illumination affect. If all of these brake light bulbs fail no brake light operation will occur. I know what you're thinking, you might say all three brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove any of the brake light bulbs to confirm the bulb is ok or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are ok continue to the next step.

on Dec 18, 2009 | Honda Civic Cars & Trucks

1 Answer

I want to know where to find my fus for the brake lights


The element inside the bulb is the fuse. When the bulb burns out you simply replace the bulb. Headlamps are the same. If you had replaced the bulb and it still does not work you need to replace the brake lamp switch which is located near the brake pedal

Apr 15, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Brake lights not working & can't find any bad fuses,& brake light switch replaced


why was brake light switch replaced? you need to check things before replacement. is the brake light switch getting power? if not the fuse is blown. if it is getting power, is power going out? if so, check for power at the bulbs, if no power find out why, if the bulbs do have power, they are not getting ground. the ground wire is in trunk, I really dont know exact location. may be near high mounted brake light.

Oct 21, 2009 | 1999 Mazda 626

3 Answers

Brake lights do not work All bulbs have been replaced.


Troubleshooting Procedures - Read Completely Before Beginning
(American Car) All Brake Lights Not Working
  • Check System Fuse: A fuse is used to protect the brake light circuit from amperage overload. If the fuse has failed it will not allow the electrical current to continue to the brake lights. To check the fuse, first locate the brake light system fuse in the fuse panel which is either under the dash or under the hood in the power distribution center. Connect the test light to a ground like an engine or dash bracket and turn the ignition key to the "on" position. Using the test light probe both sides of the fuse. If the test light illuminates on both sides the fuse is ok continue onto the next step. If one side of the fuse illuminates the fuse has failed and needs to be replaced. If the fuse fails as soon as it is replaced or when you apply the brake pedal the brake light electrical circuit is shorted to ground. Rarely a system short can occur, a car repair manual is needed to find the wiring schematic for the brake light circuit. Once the brake light wiring has been located inspect and repair as needed.
  • Check Brake Light Bulbs: All cars have three brake light bulbs that create the brake light illumination affect. If all of these brake light bulbs fail no brake light operation will occur. I know what you're thinking, you might say all three brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove any of the brake light bulbs to confirm the bulb is ok or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are ok continue to the next step.
  • Checking the Brake Light Switch: A control switch is used to connect the brake light electrical circuit. This switch is located near the brake pedal lever. Basic switches have just two wires, power in and power out to the turn signal switch. Use a test light that is grounded and with the key in the "on" position test for power at one side (wire) of the switch, then press the brake pedal while testing the opposite side (wire). It should illuminate the test light, if electrical power is connected through the switch go to the next step. If no power is detected through the switch the brake light switch has failed and replacement is required. If your car is equipped with more than two wires integrated into the brake light switch a car repair manual is needed to locate the proper brake light circuit wiring.

Jul 07, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Right brake light is out and don't know which bulb to change


Have someone apply brakes. Observe which bulb lights in the left light housing. This is the bulb you want to replace.

May 07, 2009 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Chevrolet Lumina Logo

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...