Question about 1988 Ford Crown Victoria

2 Answers

Where is the fuel pump located on a 1988 crown Vic

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 66 Answers

Inside the fuel tank

Posted on Jun 29, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 86 Answers

Check engine block lower passenger side should be easy to spot theres 2 steel lines going into it. if not check the gas tank.hope this helps you

Posted on Jun 29, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 36 Answers

SOURCE: 1999 crown vic fuel pump location

fuel pumps in the gas tank are always mounted in the top of the tank

Posted on Feb 13, 2009

  • 599 Answers

SOURCE: My 99 Crown Vic acts like it isn't getting gas

check for clogged fuel filter first, usually the pump works or it dosen't, check and get back to me.

Posted on May 01, 2009

  • 1 Answer

SOURCE: where is fuelpump on 2003 crown vic police intercepter

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

  • 1 Answer

SOURCE: Location of fuel pump relay on a 2001 Ford Crown Vic

where is the fuel pump relay on a 2001 crown vic p71

Posted on Apr 14, 2010

  • 5 Answers

SOURCE: 1988 Ford Crown Vic Horn Relay Location

The horn relay IS NOT located in a box toward the front of the engine. It is located just behind the radiator overflow reservoir and attached to the inner fender next to two other relays. It is the only one without a plastic cover over the top of it. FYI, our Crown Vic horn didn't blow, and the cruise didn't work. I changed the relay and still no horn. I decided to check the horns themselves. Found wires disconnected from terminals. Touched wire to horn terminal and horn blew incessantly. (previous owner had disconnected horn rather than diagnose why) Pulled the horn "button" from steering wheel and disconnected the wire leads and horn quit. Disassembled the "button" assembly. Foam had degraded over time between the contacts. (Ford has discontinued this part). Cleaned and replaced foam with Scotch foam mounting squares with holes punched out over contacts (2 layers thick). Re-assembled and viola! Horn and cruise control both work! Relay was bad as was horn button.

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi have a 1988 crown vic,,it will die after i drive it for about 15 mins..It is not over heating..i have to let it sit for alittle while then it starts up and run for a few mins then dies again,,is it the...


oil presser seseror or just bad pump or your oil to old and thinnig out causing lack pressure and the computer cuts it off so you dont damge enigin or there **** in your tank

May 08, 2011 | 1988 Ford Crown Victoria

1 Answer

1988 crown vic fuel injector harness both contacts lite up


sounds like your PCM might be bad if it is not supplying correct voltage to fuel injector.

Also, the fuel injector itself may be bad or bad ground.

Does it have throttle body injection on that crown vic?

Jul 10, 2010 | 1988 Ford Crown Victoria

1 Answer

Is it hard to change a fuel pump for aford crwn vic 1988 and how long?


The hardest part about replacing the fuel pump is wrestling down your fuel tank.The pump is inside of the tank and requires tank removal.As long as you own a couple of jackstands and a floor jack, you will have a fairly easy time replacing the pump itself.This should take the weekend warrior about four to five hours labor time.I hope I could help!!! Thanks for using Fixya!!!

May 12, 2010 | 1988 Ford Crown Victoria

1 Answer

Fuel pump,


For home shade tree mechanics 8 hours on average. 2 hours for a pro with the tools required for draining the tank

May 12, 2010 | 1988 Ford Crown Victoria

1 Answer

Cant loc the idle air control vavlve located on a 1988 crown vic


attached to the throttle body,looks like an electric motor bolted to a square piece with the corners notched out,with 2 wire connector on the end.

Feb 19, 2010 | 1988 Ford Crown Victoria

1 Answer

Fuel pump fuse


Replace fuel pump drawing to much resistance.

Jun 19, 2009 | 1988 Ford Crown Victoria

1 Answer

Picture location of spout on 88 ford crown 302 fuel inj


the spout connector should be in the harness at the distributor

May 02, 2009 | 1988 Ford Crown Victoria

4 Answers

My 99 Crown Vic acts like it isn't getting gas


check for clogged fuel filter first, usually the pump works or it dosen't, check and get back to me.

May 01, 2009 | 1988 Ford Crown Victoria

2 Answers

Location of fuel pump relay on a 2001 Ford Crown Vic


where is the fuel pump relay on a 2001 crown vic p71

Jan 10, 2009 | 2001 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...