Question about 2003 Lincoln Navigator

1 Answer

It works in the front and back at diffrent times

How can this be repaired?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 138 Answers

What works at different times?

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 FACELIFT LAGUNA 1.9DCI 130 DISPLAY IS SHOWING CHECK INJECTION IS THIS A COSTLY REPAIR


It means you injectors are clogging up (Sprays gas in motor) Go to parts store...Buy bottle throttle spray...not carburetor spray because it eats your rubber ceils up. Take the air duct loose from carb. While accelerating you gas throttle with your hand spray the bottle throttle spray directly into carburetor. As the car trys to stall let go of the spray...Repeat 3 or 4 times.......Ive seen the engine light go back off after doing this...It will get to your injectors and clean them...Ive done this alot myself and what a diffrents.Its works alot bettef that just adding injector fluid to gas...Promise

Aug 13, 2013 | Cars & Trucks

1 Answer

Drivers side Window not working. 93 Chevy S 10 Blazer


Well in theory you could but most motrs or diffrent sizea for the back then the front but i can not tell with yours

Dec 25, 2012 | Cars & Trucks

1 Answer

1989 toyota pickup front disk brake pads replaced, now the front calipers wont clear the new disk brake pads! Any solutions, please?


remove caliper, push disc all way home, put wheel nut on to hold home, retry fitting them the disc may be slightly scued. If no go try diffrent brand of pad I had same prob with a diffrent car last week & diffrent brand pad was 2mm thiner. If can't exchange pads get piece of emery paper on flat surface & sand away top part of pad material in round motions both ways till they fit. :-)

Jul 09, 2012 | Toyota Cars & Trucks

1 Answer

Front end shakes


Several things could cause this. Look at the inner tie rod end bushings. They are behind the engine block and are easy to replace. You can check this by holding onto the tie rods and seeing if they move back and forth. If not, the go to the tire. Holding the tire at 9 and 3 (clock times) try to shake it back and forth. If there is a lot of play (movement) This could point to either your lower ball joint/control arm assembly, or your outer tie rod ends. Both of these fixes are pretty easy if you know how to work on cars at all, but you will need to get it alligned after you are done doing the work. Also, if the lower ball joint assembly is out, a lot to times you will feel a clunk in the break pedal like your breaks are releasing at diffrent times. (you can also hear a clunk.) I have more ideas, but this is a good place to start because the parts aren't too expensive. If you need advice on replacing these parts, I can give you a hand with that too. Good luck.

Sep 22, 2010 | 2002 Dodge Intrepid

1 Answer

Want to replace front break pads


biggest difference is you should loosen the bleeder screw to press the caliper piston back in, otherwise you could damage the abs actuator, and do not disturb the wiring or sensor

Jul 19, 2010 | 2004 Honda Odyssey

2 Answers

My 2003 fanon front does not work but back does


Hello the frunt and rear fan are on diffrent switches sounds like the frunt fan switch is bad

Jul 11, 2010 | 2003 Dodge Durango

1 Answer

Timing belt marks


The crank pulley should have a mark that is approx 12 o clock with an arrow on the block. Both cams should have marks,'I' for the rear cam and E for the front, and the dowel pins (in the end of each cam)AND the marks on the cam pullies will be 12 o clock with the back cover. Be SURE you TORQUE the crankshaft bolt to 120 ft lbs.

Dec 16, 2009 | 1992 Mazda Protege

1 Answer

Misfire on #4 cylinder, plugs relaced about 20k miles ago, at shop when timing belt water pump ect done around 60k miles


faulty secondary ciol think its coil# 1 that splits with #4 only three coils on front easy to access same part
nubber try switching coils and see if diffrent miss fire

Dec 05, 2009 | 2004 Kia Sedona

1 Answer

2004 Outback Driver's Seat motor dead


Try swapping motors not brushes,maybe the motors are the same just in diffrent positions,it wouldnt be cost effective to have diffrent motors for the same job just diffrent positions,im tipping they will be the same pull seat out or lookcarefully in the car to see

Sep 20, 2009 | 2004 Subaru Outback

3 Answers

Check oil light will not reset


Try to press the gas pedal 4 times and hold it down on the 4th wait for the light to flash and go out. then start the car with your foot off the accellerator pedal. I hope this helps.
Thank You,
Roy

Aug 08, 2009 | 2005 Chevrolet Equinox

Not finding what you are looking for?
2003 Lincoln Navigator Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...