Question about 1996 Nissan Quest

1 Answer

The A/c does not work in the rear.I have a 1996 nissan quest

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 4,369 Answers

You have a bad solder joint in your heater control head. If you can solder, you can fix it. I will fix it for $25 and send you a control head. Then you send yours back to me.

Here's our Villager/Quest web site.

http://groups.yahoo.com/group/villagerquest/links

The A/c does not work in the rear.I have a 1996 - 4b29200.jpg
You have to remove 4 plastic screws on console bottom. Then remove 2 screws at bottom of center trim panel. Then remove ash tray and 2 screws just above tray opening. Then 2 screws at top of center trim panel. Then pull off center trim panel. It has 2 spring clips in center.
Then remove 4 screws holding control head in.
Remove all electrical connectors.
remove thin plastic cover on bottom of unit. 2 plastic clips hold it on.
remove circuit board, and look on back side for crack around solder joint that is circled in red on picture. Or the joint next to it.
resolder the cracked joint. Don't heat the joint too much. Just enough to get solder to drop on to it.

Posted on Jun 30, 2009

  • gerry bissi Jun 30, 2009

    PS. A new control head is $400 and most used ones have the same problem

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

justuscc
  • 360 Answers

SOURCE: Nissan Quest 1996 minivan

you need to remove the lower balljoint and the center nut and it should come right out. use pb buster or wd-40 on the splines. they tend to rust up

Posted on Oct 02, 2008

  • 840 Answers

SOURCE: replacing belts after replacing water pump on 1996 nissan quest x

the easist way is to loosen the alternator slide the alternator down then slide the belt where it should go then pull up on the alternator again and bolt up Please rate my response thank you very much

Posted on Jan 30, 2009

pippall
  • 1486 Answers

SOURCE: 1994 nissan quest crankshaft rear main seal removal

There is no other way other than to remove the engine.I now its a lot of work but if you want to do the job properly then thats the way to do it.You can remove the gearbox and try.I think thats a waist of time good luck.

Posted on Jul 28, 2009

greg_margo
  • 1959 Answers

SOURCE: Will you provide belt diagram for 1996 nissan quest?

There are 2 diagrams available:
7aa2154.gif

8d91591.gif

Posted on Aug 13, 2009

bolinlamar
  • 157 Answers

SOURCE: 1998 Nissan Quest - rear blower not working

SInce you indicated that it was working intermittently then quit working altogether the most likely culprit is probably a bad blower relay . The Contacts in a relay will sometimes burn and intermittently still conduct for while until they get so burnt that they won't conduct at all and the relay will have to be replaced. If you could get a Chilton Service Manual for the Vehicle in question it would probably show the exact location of the relay.

Posted on Sep 02, 2009

Testimonial: "Thank you. The relay was my next stop. I have had the dash apart already and checked all the connections on the control panel."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 nissan quest rear ac not working


i have 1997 nissan quest Ac and heat flow at front working but rear not work please tell me the problem

Jul 02, 2012 | 1998 Nissan Quest

1 Answer

1996 Quest: how many miles to replace timing belt for nissan q...


it's a freewheeling engine. Interval is 105,000 but most go to 160,000 easily.

I would just kep driving, no engine damage will happen if it breaks. engine will just stall.

http://groups.yahoo.com/group/villagerquest/

May 18, 2010 | 1996 Nissan Quest

3 Answers

Nissan Quest 1996 won't start. Battery good.


tap the starter at the same time turning the key. if it starts ,replace starter.

Mar 14, 2010 | 1996 Nissan Quest

1 Answer

How to replace rear main oil seal on a 1996


big job you might have to pull the transmission out to do it

Mar 09, 2010 | 1996 Nissan Quest

1 Answer

My 1996 Nissan Quest car stereo stopped functioning


YOU MAY WANT TO TRY DISCONNECTING THE BATTERY OVER NIGHT I KNOW IT WORKS ON FORDS

Mar 04, 2010 | 1996 Nissan Quest

1 Answer

1996 nissan quest blower wont work. checked


There might be some heavy resistance with one of the wires leading to it. Have an electrician check it out.

Jul 14, 2009 | 2002 Nissan Pathfinder

2 Answers

Nissan quest 1996 cigarette lighter fuse locati


Check the cigar lighter fuse for blown.

Jun 05, 2009 | 1996 Nissan Quest

1 Answer

97 Nissan Quest - odometer is not working


remove the 2 wire connector from the VSS, vehicle speed sensor on the top rear of the trans.
clean the VSS and the wire terminals with a terminal cleaner from radio shack.

go here for pictures, files on speedo, etc.

http://autos.groups.yahoo.com/group/villagerquest/files/

Apr 01, 2009 | 1996 Nissan Quest

1 Answer

Replacing belts after replacing water pump on 1996 nissan quest x


the easist way is to loosen the alternator slide the alternator down then slide the belt where it should go then pull up on the alternator again and bolt up Please rate my response thank you very much

Jan 29, 2009 | 1996 Nissan Quest

1 Answer

Nissan Quest 1996 minivan


you need to remove the lower balljoint and the center nut and it should come right out. use pb buster or wd-40 on the splines. they tend to rust up

Oct 02, 2008 | 1996 Nissan Quest

Not finding what you are looking for?
1996 Nissan Quest Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...