Question about 2004 Chevrolet Venture Passanger

1 Answer

Where is the (front) blend door actuator located in my 2004 vhevy venture & is it difficult to get to?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Of course it is it's never to get to anything on cars it's under the dash on the right side but you are looking at blend door but why? do you understnd the operation of them? if not you do not know what your looking for, as there are three on the car and figueing out witch one you need to look at.

Posted on Jun 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat only blows on the floor and the defrost but not in all vents across the front. Wher is the location of my blend door actuator


Hi Chris,

I had a similar problem with my 04 Envoy.. here's what to do: Disconnect the (+) battery cable from the (+) post for 30 seconds or so, then reconnect. This process "calibrates the blend door as it cycles it from one extreme to the other. Start the truck and check it out.

If this doesn't work, more drastic measures will be needed. I hope this helps & good luck!

Mar 05, 2013 | 2004 GMC Envoy

1 Answer

Blend Door Actuator possibly bad


Not to difficult but you may need to get smaller tools to make it easier or possible depending on the tools you have now.

Jul 18, 2012 | 2004 Kia Sedona

1 Answer

Blend door actuator possibly bad how hard is it to fix or replace?


usually it is in the dash and the glove box needs to be removed to get to the actuator.

Jul 18, 2012 | 2004 Kia Sedona

2 Answers

Front a/c blows but is not cooling. Rear air works just fine?


check front blend door actuator may be binding keeping heater core exposed to blower motor flow

May 09, 2011 | 1998 Lincoln Navigator

1 Answer

My 2004 Avalanche ' heating system will not heat. No matter what the setting it either blows no air or cold air and it is 25 degrees outside so this is a problem. The engine is up to temp and I have tried...


The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation
  1. Remove the floor air outlet duct extension (1) from the floor duct (2).

    jturcotte_393.gif

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)


Disconnect the electrical connection at the blend door actuator (#10 in pic below). jturcotte_394.gif

Fig. Blend door actuator and related components


Remove the blend door actuator mounting screws from the HVAC module.


Remove the blend door actuator as an assembly with the actuator cam.
jturcotte_396.gif

Fig. Remove the blend door actuator mounting screws from the HVAC module



To install:

  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam

  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).

  3. Connect the electrical connection at the blend door actuator (10).
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).


Picture of actuator:


jturcotte_57.jpg

Dec 07, 2010 | 2004 Chevrolet Avalanche

2 Answers

2004 f350 ford heater blows cool air but hoses are both warm-where do i start looking


check to see if the blend door is moving where you change the temperature setting. I think your blend door is behind the glove box. Here are instructions for removing the actuator. Take it off, plug it back in and see if the motor rotates. Also check to see if you can rotate the blend door by hand. If you can rotate it by hand, the motor is probably broken of the gears are stripped. Let me know if you have questions.
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
f4b0b74.gif Fig. Blend door actuator-F-250 & 350


  1. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  2. To install, reverse the removal procedure.

Oct 17, 2010 | 2004 Ford F350

1 Answer

Ned to know where the blend door actuator for the front of the vehicle is located in my 2004 chevy venture


i think it is on the air distribution box and alot of times you have to take it out to take the actuator off which requires removal of the dash

Jun 29, 2009 | 2004 Chevrolet Venture Passanger

1 Answer

2004 chevy venture only gets hot air in front, rear a/c works great...is the front dampers stuck? How do I fix that?


No real solution...needs a blend door actuator, which is VERY expensive because it requires the removal of the dash board. (about 10to 12 hours labor alone)

May 07, 2009 | 1999 Chevrolet Venture

3 Answers

01 silverado blend door changed /now works back wards!!!


most likely needs a LH (bottom) temp actuator. Located in the center of the dash on the bottom, you have to remove the hush panel on the rh side of the truck

Apr 24, 2009 | 2001 Chevrolet Silverado

Not finding what you are looking for?
2004 Chevrolet Venture Passanger Logo

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...