Question about 2002 Mercury Mountaineer

1 Answer

Door ajar warning

The "door ajar" warning intermittently comes on when all doors are closed

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Spray wd40 into each of the latches, chances are dirt has built up on the switch located inside the latch

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to diagnose which door is causing the door ajar warning on dic for 08 pontiac g6 4cyl 4dr


It should tell you which one .
Driver Door Ajar Malfunction
Passenger Door Ajar Malfunction
If not a scan tool would be the best way.
Ignition ON, observe the scan tool Driver Door Ajar Sw parameter while opening and closing the driver door. The parameter should change between Door Closed and Door Ajar
? If the parameter does not change, refer to Driver Door Ajar Malfunction.
With the passenger doors closed, observe the scan tool Door Ajar Switch parameter while opening and closing each door. The parameter should change between Door Closed and Door Ajar.
? If the parameter does not change, refer to Passenger Door Ajar Malfunction

Ignition OFF, disconnect the harness connector at the driver door latch.
Test for less than 5 ohms between the ground circuit terminal 8 and ground.
? If greater than the specified range, test the ground circuit for an open/high resistance.
Ignition ON, verify the scan tool Driver Door Ajar Sw parameter is Door Closed.
? If not the specified value, test the signal circuit terminal 6 for a short to ground. If the circuit tests normal, replace the BCM.
Install a 3A fused jumper wire between the signal circuit terminal 6 and the ground circuit terminal 8. Verify the scan tool Driver Door Ajar Sw parameter is Door Ajar.
? If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
If all circuits test normal, test or replace the driver door latch

Dec 26, 2016 | Pontiac Cars & Trucks

1 Answer

Peugot partner mpv 2002,door ajar warning on all time central locking bounces/wont stay locked and door ajar buzzer sounds with rh indicator...HeLp


check all of the door sensors. (buttons that are pushed in when doors close) they sometimes come loose and need adjusting.. easy fix once you find the bad one.

Feb 07, 2014 | Peugeot Cars & Trucks

3 Answers

How can I fix a door adjar error on a 1999 Lincoln Continental? When the drivers door is shut, the warning comes on and the dome lights remain on. I don't want to spend money to replace the sensor, but can...


I suspect you have a bad door ajar switch on one of your doors.

The switch is on the door latch. try pushing each door in with your hand one at a time and see if the warning goes away.
The Lighting control module is $500 and controls a lot of the vehicle functions. It is part of the headlamp switch. It has to be configured by the dealer with his NGS tester before it will work. Ebay has them cheap sometimes. Only buy Continental LCM for your model year.



info
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
-----------------------------------
Visual Inspection Chart Mechanical Electrical
  • Door ajar switches.
  • Fuse junction panel fuse 28 (10A), 4 (10A), 5 (10A).
  • Power distribution box fuse 6 (60A).
  • Circuitry.
  • Damaged or corroded connectors.
  • Lighting control module (LCM)
  • Driver door module (DDM).
  • Virtual image cluster (VIC).
  • Restraint control module (RCM).
  • Low tire pressure module.

------------------------------------------------------------
  • The Door Ajar Chime Does Not Operate Properly
  • LCM.
  • Driver door ajar switch.
  • Passenger door ajar switches.
  • Key warning switch.
  • Circuitry.

-------------------------------------------------------------
remove the door trim panel to access the door ajar switch.

0339bdb.gif
Remove the door open warning switch by turning it counterclockwise.
----------------------------------------------------------------------------
Trim Panel —Front Door Removal
  1. Remove the screw cover.
  1. Remove the screws.
  1. Remove the front door trim panel (23942) from the door.
  1. Disconnect the electrical connectors and remove the front door trim panel.
Installation
  1. Follow the removal procedure in reverse order.

Aug 28, 2009 | 1999 Lincoln Continental

1 Answer

Warning driver door not shut, beeping every few minutes. door !


either door ajar switch is bad or door jamb push button is bad or not plunging all the way in.

May 22, 2009 | 2004 Renault 181

3 Answers

Door ajar or the message board


all the doors and trunk lid have switches fitted to them, these switches sense if he door is not closed, the problem is they stick and then then u get the door ajar warning, the lincoln dealer can isolate the sticky switch very quickly with an electronic scan tool, the part is cheap about $12

Apr 07, 2009 | 1993 Lincoln Mark VIII

1 Answer

Key on engine running trouble code 55


Warning Chime Systems The generic electronic module (GEM) will sound the following warnings:
  • key-in-ignition warning
  • safety belt warning
  • headlamp switch ON warning
  • door ajar warning
------------------------------------------------------------------------------------------------
Headlamp Switch On Warning The generic electronic module (GEM) sounds when the driver door is opened while the headlamp switch (11654) is in the PARK or HEAD position, and continues to sound at a rate of 4 chimes per second until the headlamp switch is turned off or the driver door is closed.
  • When the headlamp switch is in the PARK or HEAD position, power is supplied through Circuit 293 (O/R) to the GEM.
  • When the driver door is open, the driver door open warning lamp switch (10B997)is closed and ground is supplied to the generic electronic module (GEM).
A delayed headlamps on repetitive chime will sound for a period of three seconds beginning twenty seconds after the key is turned to OFF, LOCK or ACC, the headlamp switch is in the PARK or HEAD position, and the driver door is closed. Delayed headlamps on is terminated by opening and closing the driver door again.
---------------------------------------------------------------------------------------
Door/Liftgate Ajar Warning The door/liftgate ajar warning functions as follows:
  • The generic electronic module (GEM) sounds a warning tone for one second when any vehicle door, liftgate window or the liftgate is ajar without any other door already open and the ignition switch is in the RUN position.
  • Power is then supplied through Circuit 627 (BK/O) to the door ajar warning indicator lamp which remains illuminated until all doors are closed or the ignition switch is no longer in the RUN position.
----------------------------------------------------------------------------------------------
Key-in-Ignition Warning The generic electronic module (GEM) sounds when the LH front door is opened with the key in the ignition switch and continues to sound until the key is removed or the door is closed.
  • When the key is in the ignition switch, the ignition key warning switch terminal and wire (11A128) is closed and ground is supplied through Circuit 158 (BK/PK) to the generic electronic module (GEM).
  • When the LH front door is open, the LH front door open warning lamp switch (10B997) closes and ground is supplied through Circuit 57 (BK) to the generic electronic module (GEM).
-------------------------------------------------------------------------------------
Safety Belt Warning When the ignition switch is turned to RUN or START from the OFF or ACC position and remains in RUN or START, the chime will sound for six seconds or until the safety belt is buckled. The safety belt warning indicator lamp (10C859) will turn on for 60 seconds, or until the LH front safety belt is fastened. Both the chime and lamp activate at the same time. If the safety belt is buckled when the ignition key is turned to RUN or START from OFF or ACC, the lamp will prove out for two seconds, but chime will not be activated. Any time the key is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Feb 25, 2009 | 1999 Ford Taurus

2 Answers

Ignition alarm will not stop 97 ford f150


The key switch usually breaks or wears out and makes contact. It is on the lock cylinder. This would cause the chime to not come on, or stay on. Sounds like the switch is bad.

1997 F-150/250 Warning Chime, Key-In-Ignition The key-in-ignition chime warns that the key is still in the ignition when the driver's door is ajar. The key-in-ignition warning chime will sound when:
  • GEM: Driver door is ajar, the ignition switch is in the OFF/LOCK or ACC position and the keys are in the ignition.
  • CTM: Driver door is ajar, the ignition switch is in the OFF/LOCK, ACC or RUN position and the keys are in the ignition.
The key-in-ignition warning chime will stop sounding when:
  • Driver door is closed.
  • Key is removed from the ignition.
  • GEM: Ignition switch is switched to the RUN position.
The key-in-ignition warning chime inputs are:
  • Ignition switch RUN position (battery potential on both RUN and RUN/ACC inputs).
  • Ignition switch ACC position (battery potential on RUN/ACC input only).
  • Key-in-ignition switch (grounded with key-in-ignition, open circuit with key-out).
  • LH door ajar switch (open circuit with door closed, grounded with door ajar).
This is a pic for a 98, could not find one for 97 which may be the older style which is more prone to break.
5a6d33c.gif

Feb 14, 2009 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
2002 Mercury Mountaineer Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...