Question about 2006 Hyundai Tiburon

1 Answer

How do i change the back brakes on a 2006 tiburon

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Disk Brakes - remove two 14mm bolts which mount the caliper to the rear hub assy. Remove the caliper. Remove the phillips screw which holds the rotor to the hub. Machine the rotor and reinstall on the hub & reinstall the phillips screw. Reinstall the caliper and remove one of the caliper hinge pin (sliding pin) 14mm bolts. Flip the caliper out of the way and replace the pads and anti-rattle springs. Recompress the caliper piston all the way back into its cylinder. Flip the caliper back into position and reinstall the 14mm bolts. Of course, you need to purchase the replacement pads and w/anti-rattle springs.

Posted on Jun 30, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: change brake light switch

The switch is located under the drivers side dash behind the brake peddle arm.

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What brake pads where used on Hyundai Tiburon 06 SE?


OEM were these
http://www.carid.com/2006-hyundai-tiburon-brakes/powerstop-1-click-oe-replacement-brake-kit-31487698.html

Oct 31, 2014 | 2006 Hyundai Tiburon

1 Answer

Front driver and rear passenger brakes wont bleed? 06 hyundai tiburon


thought the tyre shop should have known ,this vehicle has ABS and depending on the system you cannot bleed the brakes without dealer software to make the ABS system open to allow the fluid through .Sorry got to go first customer here

Apr 01, 2012 | 2006 Hyundai Tiburon

1 Answer

I was told the rear right hub bearing went out, so i ordered one from auto zone but it doesn't fit. It is to loose what do i do?? Also when i back up the car makes some really loud noises. (this just...


1st, take the hub bearing back to AutoZone and either get you money back or get them to order or give you the right size bearing. The noise you are having could be from that bearing.... ya think?

Sep 05, 2011 | 2006 Hyundai Tiburon

1 Answer

How to change a battery for 2006 Hyundai Tiburon GT? Theres a nut with a washer that is screwed down on the battery terminal


Just remove the nut and washer on both post. If you have a rod that locks the battery down, loosen it up so you can remove the clamp that holds the battery down.
Remove negative battery cable first, then positive cable.
When putting the cables back on, positive gets put on first, then negative.

Sep 29, 2010 | 2006 Hyundai Tiburon

1 Answer

How do you replace the brake light in a hyundai tiburon


Hello There,

As there are three break lights on the Tiburon (2 sides, 1 centre top) I will post solutions for all of them.

2 side brake lights:
open the hatch, inside on each side of the boot you will find a small carpeted door. take it out and reach through until your hand is directly behind the light cavity. Unscrew the cap to the light cavity and there will be a fastener holding the light bulb firmly in place. to remove fastener push it in and then move it to either left or right depending on which side your changing over, release it and move it out of the way. pull out bulb. to replace repeat these steps but in reverse. Remember it is very important to replace fastener back so it is holding bulb firmly in place

1 centre brake light:
unscrew the base of the light carriage or unclip - depending on make/model. Unclip fastener from bulb. You will then be able to replace the light bulb with ease. Remember it is very important to replace fastener back so it is holding bulb firmly in place.

Hope this helps,

Cheers Buckaroo,
Chris.


WARNING :
Do not touch light bulbs with bare fingers as it inhibits performance and your bulb may not work. Gloves should be worn at all times when dealing with glass.

Apr 20, 2010 | 2006 Hyundai Tiburon

1 Answer

Can't get the brakes to bleed to a 2006 hyundai tiburon


The tiburon's brakes are simple, there's no special technique to bleeding them. Are you sure you're bleeding them correctly?

If you are bleeding them correctly, then it's possible that you have a brake leek, causing air to get into the system.

Apr 03, 2009 | 2006 Hyundai Tiburon

1 Answer

How do you bleed the brakes to a 2006 hyundai tiburon


Go to the r/r caliper, pump the brake pedal three times and hold down, open bleeder to run fluid out, close bleeder, let foot up off brake pedal. Repeat LR, RF, LF calipers. This is called a pressure bleed. Take note whether you got any air out of the bleeders.

Apr 03, 2009 | 2006 Hyundai Tiburon

1 Answer

Change brake light switch


The switch is located under the drivers side dash behind the brake peddle arm.

Mar 22, 2009 | 2006 Hyundai Tiburon

1 Answer

I have an 06 hyundai tiburon gt v6 and im replacing the rear brake pads but the caliper pistons seem to be stuck! is there any way they are tied into the front brakes r is this just stuck caliper...


On cars with 4 wheel disc brakes the rear calipers are what they call racheting.The pison needs to be turned clockwise at the same time you are pushing in.This mechanisum is for the E brake system.They make special tools for doing this that you can pick up at your local parts store.

Mar 04, 2009 | 2006 Hyundai Tiburon

Not finding what you are looking for?

Open Questions:

0 Answers

Shifting problems My car is a 2006 Hyundai Tiburon, Automatic, 2.0L 4 Cylinder I've had the car two years I don't know what's related and what isn't so here is the story. Bought car, (cruise control did not work) but everything else seemed fine, engine light came on code read Vehicle Speed Sensor so I bought an input and an out transmission speed sensor and had them installed, Motor blew 2 heads had motor replaced with an almost new motor. Cruise control now works, three days later car would not come out of park shifter moved but car stayed in park felt like shifting cable let loose, I called a backyard mechanic friend and he moved the shifter hard and it went into drive said probably buddy who changed motor forgot to unhook cable and stretched it (made sense to me) it did this everytime car was put into park had to yank on the shifter to get it to shift so I started parking her in neutral and it never messed up, after 3 weeks my new shift cable came in so I went to show my mechanic what car was doing it wouldn't do it worked fine, told him I'd call him next time it messed up this is a year and a half later hasn't messed up like that again! I had already bought the cable so I decided to have it installed anyways even though problem seemed fixed went to a shop they told me nothing is wrong with my cable..... Approx 6 months ago put car into drive and started driving the car reved out (I call it) motor got really loud and RPM gage went to 4K and car jerked really bad and made a really loud snap noise so I pulled over and roughley shift car into park and back into drive and drove this fixed the issue for that drive anyways.... my car one day over heated to red line in a 5 minute drive in the winter my mechanic said must be an air lock so he drained my fluid and replaced ect, next day car wouldn't start, blew starter, replaced that, next day driving car and in a 5 minute drive it overheated to red line took car to shop he said gage is reading wrong car is barely even warm so I decided to take the car home and worry about this issue pay day well the next day car wouldn't start, blew alternator, at this time my mechanic looked over car more closley turns out I had a bad ground so he put on new alternator and new ground, this was a month ago and no more issues with overheating or not starting. However I still have this issue (copy and paste) "put car into drive and started driving the car reved out (I call it) motor got really loud and RPM gage went to 4K and car jerked really bad and made a really loud snap noise so I pulled over and roughley shift car into park and back into drive and drove this fixed the issue for that drive anyways...." After having ground put on and shifting issue still there I took my car directly to Hyundai they ran all their computer tests and transmission tests and took car for a test drive car worked fine and only code that came up was Vehicle Speed Sensor. So here is where I stand first question how many speed sensors does my car have is a transmission input/output speed sensor different then a vehicle speed sensor? I looked on parts sites and only speed sensors I find are ABS speed sensor and Vehicle Speed Transmisson Sensor, so maybe sensors I bought are no good but they were bought new or maybe the connector for the sensors are bad? I don't know any suggestions would be greatly appreciated.

Jan 12, 2016 | 2006 Hyundai Tiburon

See all 2006 Hyundai Tiburon Questions

2006 Hyundai Tiburon Logo

1,073 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...