Question about 2000 Lexus Gs 300

1 Answer

How to remove and replace the front brake pads and rotors

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lexus Master
  • 75,822 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front brake pads


1. Raise vehicle
2. Support on jack stand
3. Remove lug nuts
4. Remove wheel
5. Remove bolts holding caliper
6. Remove calipers
7. Remove brake pads
8. Push piston into caliper
9. Inspection rotor for damage if damaged replace
10. Install new pads
11a. Replace caliper on rotor
11 b. Replace bolts in caliper and tighten
12. Bleed brakes
13. Replace wheel
14. Replace lug nuts
15. Lower vehicle
16. Tighten lug nuts
17. Test drive vehicle

Oct 17, 2015 | 2004 Chrysler Sebring

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

3 Answers

WHy dose my brake pedal push back and make a grinding noise


Look through the openings in your front wheels and look at the front rotors-are they gouged up? You are probably running metal-to-metal, pads to rotors.
Chances are real good your rotors will have to be replaced along with new pads, but if you catch it early enough you might be able to have them machined, although nowadays that is hardly easy to get done and the savings usually is not as significant as it once was.

May 23, 2011 | 1995 Pontiac Bonneville

1 Answer

Should the center spindle nut and 2 torgued phillip head screws be removed to replace front brake rotor on 1999 honda accord lx


will try to help. 1st remove the wheel, then remove the 2 caliper bolts that hold the brake caliper on. after removal of brake caliper, [it should just pull off after the 2 bolts are removed] replace the brake pads[be sure to apply anti squeal lube to the outer side of the pads..not the pad itself,the one not contacting the brake rotor] install the pads, the you will need a C clamp to push the brake caliper pistons back into the caliper. i've used this installation easily. use the old pad ,place it against the caliper piston,then apply the C clamp and push the caliper piston back into the brake caliper, then the brake caliper will slide back over the new pads easily, no need to bleed the brakes if you use this solution. replace the brake caliper bolts, then go to next side and repeat the process. after the replacement of the front brake pads,pump the brakes with engine running!!! it's really a simple process. be sure the brake pads are facing the brake rotors with the [pads] facicing the rotors. no metal facing metal. easy! if you have added brake fluid recently, do not be alarmed if you see fluid coming out of the brake master cylinder,when you use the C clamp to collaspe the brake caliper back into the recessed position. [as always when you have to add brake fluid to the brake master cylinder,it only means your brakes are wearing naturally. if you have a vibration in front wheels or steering wheel when braking, you have a brake rotor or both front brake rotors that need replacement with your brakes also. hope this helps and as always, please get a second opinion if you have doubt. an expert will be happy to help. thank you for choosing fixya.com

Dec 22, 2010 | 1999 Honda Accord

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

Brake pad replacement 2004 audi a4 and rotor how do i do and what tools are neccessary?


YOU NEED REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER.THEN YOU RAISE VECHICLE SAFELY.SUPPORT IT WITH JACK STAND.MAKE SURE VECHICLE IS ON LEVEL SOLID GROUND.REMOVE TIRE OR WHEEL.THEN YOU NEED A LARGE C - CLAMP.PLACE C - CLAMP OVER BRAKE CALIPER AND BRAKE SHOE BACKING.TIGHTEN C - CLAMP JUST ENOUGH PUSH CALIPER PISTON BACK IN CYLINDER BORE TO REMOVE CALIPERS FROM ROTORS.TO REMOVE BRAKE CALIPER YOU NEED 2 OPEN AND BOX END WRENCHES ONE TO HOLD CALIPER SLIDE PINS AND THE OTHER WRENCH FOR LOOSEN CALIPER BOLTS.THEN YOU REMOVE CALIPER AND REPLACE FRONT BRAKE SHOES.IF YOU NEED TO REMOVE BRAKE ROTORS JUST REMOVE THE BRAKE CALIPER CARRIER SUPPORT BOLTS THE REMOVE THE BRAKE CALIPER CARRIER SUPPORT THEN REMOVE ROTOR.YOU NEED TO REPLACE BOLTS WITH NEWS AND USE LOCK TIGHT.THEN YOU PUT IN NEW BRAKE PADS IN CALIPER PUT CALIPER BACK ON SUPPORT CARRIER.REPLACE WITH NEW BOLTS USE LOCK TIGHT THEN TORQUE BOLTS TO 26 FT LBS.MAKE SURE MASTER CYLINDER COVER IN PLACE.WHEN YOU FINISH REPLACING BOTH FRONT BRAKE PADS PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST BRAKE ROTORS SO YOU WILL HAVE FIRM BRAKES WHEN YOU APPLY THEM. THEN CHECK YOUR BRAKE FLUID LEVEL IN MASTER CYLINDER MAKE SURE ITS NOT LOW. MAKE SURE YOU HAVE FIRM BRAKES BEFORE DRIVING.IF YOU HAVE ANY PROBLEMS CHANGING FRONT BRAKE PADS YOU CAN GO TO ANY AUTO PARTS STORE AND BUY A HAYNES REPAIR MANUAL.

Jun 16, 2010 | 2004 Audi A4

1 Answer

How to replace front rotors on a 1989 190e mercedes?


Remove tyres. Remove brake pads.
Remove Brake calipers bolts from the back of calipers.
Put calipers aside without removing brake lines. Remove rotor bolts. Remove rotors. Install new rotors Make sure new rotors are clean from any grease that comes on it with petrol or any cleaning chemical for that purpose (no water) Install calipers Install new brake pads Good luck

Oct 20, 2009 | 1989 Mercedes-Benz 190

1 Answer

Rumbul nnoise in front when brakes are appled


The brake pad is worn down to the rivet that holds the pad to the base.
The metal rivets are in contact with the metal brake rotor.
Metal-against-metal...
Replace both front brake pads and at least one rotor.
You should be able to see both front rotors w/o removing the wheels.
The rotor with rings like Saturn (the planet) is the one to replace.

Replace soon before the other rotor meets the same fate.

Hope this helps!

Sep 11, 2009 | 2000 Pontiac Grand Prix

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

92 960 wagon with ABS.


Very easy. Jack up the front of the car and support it with two sturdy jackstands. Remove the front wheels. To the brake fluid nipple on the caliper (the part that squeezed the pads against the rotor), attach a small tube leading to a drainpan, open the nipple, and push back the brake pads from the rotor with a broad screwdriver. Close the nipple. Be careful not to damage the pads if you are not replacing them. (It would be wise to replace the pads when you replace the rotors, though).

Two bolts hold the brake caliper onto the steering knuckle. Remove both bolts, preferably with an impact wrench, and remove the caliper. On some cars the bolts have indented 10mm hex-wrench heads rather than standard bolt heads, so you may need to acquire a new tool. Be careful to support the caliper so you do not damage the hydraulic brake hose. Slip the old rotor off the studs and replace it with your new one. New rotors are packed in oil which will damage your brake pads, so clean the new rotors with vinegar before installing them. Replace the caliper and pads. Check to see you have sufficient brake fluid in the master cylinder reservoir before operating the vehicle. If the brakes seem at all spongy, bring your car to a qualified mechanic to inspect your work and to bleed the brake hydraulic syatem. Always do both front rotors, never just one. Otherwise, your car will **** violently to one side when you brake.

Oct 03, 2008 | 1996 Volvo 960

Not finding what you are looking for?
Cars & Trucks Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...