Question about Mitsubishi Minivan

1 Answer

Hello, I have a 1996 spacegear and the front interior heater will not work (fan ok) how & where do I access the heater unit? Thank you, David

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 2,984 Answers

From the insode of the van behind the dash.

Posted on Jun 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford Focus Mk1 fuse/fuses for heater fan & interior/courtesy lights


interior fuse box lower dash drivers side , cover/lid will list the locations

Nov 07, 2014 | Ford Focus Cars & Trucks

1 Answer

How can i get the heater core out of my 2006 toyota corolla


Hello, the heater core is a small heat exchanger located inside the truck, similar to the radiator at the front of the truck. Coolant is circulated from the engine through the heater core and back to the engine. The heater fan blows fresh, outside air through the heater core; the air is heated and sent on to the interior of the truck. For Toyota Pick-ups/Land Cruiser/4Runner 1989-1996 check this reference repair guide...



Heater Core - REMOVAL & INSTALLATION
(see Figure 1)
  1. Drain the cooling system.
  2. Remove the heater unit assembly. Have a lot of towels handy for the leakage of coolant that may spill into your interior.
  3. Remove the fasteners securing the core to the unit, remove the plates and clamps. Pull upwards to remove the core from the unit.
To install:
  1. Inspect the core fins for any blockage. Using compressed air, clean them.
  2. Install the core into the unit placing the plates and clamps into position. Tighten the core screws.
  3. Install the heater unit into the vehicle.
  4. Fill the cooling system.
85a96e3.jpg

Thanks

Aug 12, 2010 | Toyota Corolla Cars & Trucks

1 Answer

Replacing heater core in a 1995 Toyota 4Runner


The heater core is a small heat exchanger located inside the truck, similar to the radiator at the front of the truck. Coolant is circulated from the engine through the heater core and back to the engine. The heater fan blows fresh, outside air through the heater core; the air is heated and sent on to the interior of the truck. For Toyota Pick-ups/Land Cruiser/4Runner 1989-1996 check this reference repair guide...



Heater Core - REMOVAL & INSTALLATION
(see Figure 1)
  1. Drain the cooling system.
  2. Remove the heater unit assembly. Have alot of towels handy for the leakage of coolant that may spill into your interior.
  3. Remove the fasteners securing the core to the unit, remove the plates and clamps. Pull upwards to remove the core from the unit.
To install:
  1. Inspect the core fins for any blockage. Using compressed air, clean them.
  2. Install the core into the unit placing the plates and clamps into position. Tighten the core screws.
  3. Install the heater unit into the vehicle.
  4. Fill the cooling system.
85a96e3.jpg

Fig. 1: Exploded view of the heater unit assembly-1996 4Runner shown





Heater Unit - REMOVAL & INSTALLATION
(see Figure 1)

Have alot of towels handy for the leakage of coolant that may spill into your interior.
  1. Discharge the A/C system (if applicable), using an approved recovery/recycling machine.
  2. Remove the cooling unit (if applicable).
  3. Drain the cooling system.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Disconnect the hoses to the heater core. Tag each one so that it may be correctly reinstalled.
  2. On some models you will need to remove the glove box assembly. On others, the instrument panel and reinforcement.
  3. At the heater case under the dash, disconnect the ductwork from the case.
  4. Disconnect the heater control cables from the heater case. Lift the spring clip holding the control cable to allow the cable to be manipulated. Don't deform or crimp the cables.
  1. Disconnect the wiring harness to the blower fan.
  2. Remove the three or four bolts holding the heater case to the dash. Because the inlet tubes project through the firewall, the unit will not fall straight down. It will need to be pulled into the passenger compartment and then brought downward.
To install:
  1. Lift the case into position and carefully place the inlet and outlet pipes through the firewall. Install the retaining bolts holding the case to the dash.
  2. Connect the wiring harness to the blower fan.
  3. Connect the control cables to their linkages. Each must be adjusted so that the motion of the dashboard lever causes the correct corresponding motion in the air door. Both the control lever and the door must reach maximum travel at the same time if full function is to be achieved.
    1. Set the dashboard control to FRESH. Lift the adjustment clip and adjust the air inlet cable towards the heater unit until the linkage is at its maximum travel on Pick-Up and 4Runner. For Land Cruiser, adjust the cable away from the case. Release the adjustment clip.
    2. Set the dashboard control to VENT (Pick-Up) or DEF (4Runner and Land Cruiser). Lift the adjustment clip and adjust the air flow control cable towards the heater unit until the linkage is at its maximum travel. Release the adjustment clip.
    3. Set the temperature control to COOL. Lift the adjustment clip and adjust the air mix control damper control cable away from the heater case until the linkage is at its maximum travel on . For Land Cruiser, adjust the cable towards the case.
  4. Connect or reinstall the ductwork. Make certain each tube is firmly and completely fitted on its port. A light spray of glass cleaner serves as a good lubricant; don't use too much.
  5. Install the glove box and/or instrument panel assembly.
  6. Connect the heater hoses. Use new clamps.
  7. Install the cooling unit (if equipped).
  8. Refill the coolant, then charge the A/C system (if equipped).



Hope this help (remember comment and rated this).

Aug 02, 2010 | 1995 Toyota 4Runner

1 Answer

How do I remove 1996 honda accord heater fan switch? I'm not sure if I need a new switch. Heater fan works only on high speed "4"


if the fan/motor only works on max No 4 setting ? then may i suggest you have a resistor fault or commonly known as a reostat in uk this is the component that provides the relevent reduced speeds on selection but when it fails only max speed works so you should find this unit attached on heater fan exterior if you follow wires from actual motor it will connect to the resistor unit ? then onward to switch control it is not to difficult diy and if you have access to manual/ it will give location/access for renewing? hope this helps/inspires you to diy ?

Dec 23, 2009 | 2000 Honda Accord

1 Answer

C180 heater fan not working all fuses ok ???


Most likely the switch or the fan motor it self.

Aug 08, 2009 | 1996 Mercedes-Benz C-Class

1 Answer

2000 Dodge Caravan Sport. Heater and AC quit working.


these heater control units were in a bad spot..cup holder right below..coffee spills have been known to get in control unit..can be expensive to replace..try a wrecking yard

Mar 20, 2009 | 1996 Dodge Caravan

1 Answer

Heater works but defrost fills inside with fog.


your heater core has probably sprung a leak.does the fog smell kinda sweet?....check the floor in the front where the floor mats are for moisture or even puddles of antifreeze.(the replacement of a heater core can be very expensive as the entire dash usually needs to be removed to access the heater core)also look under the engine near the firewall for antifreeze drips.

Dec 13, 2008 | 1998 Dodge Caravan

1 Answer

Fan heaters


Just take a test light and check them all.

May 28, 2008 | 1996 Ford Escort 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...