Question about Isuzu Rodeo

1 Answer

It gets better

After sitting overnight, it fired right up, let it idle bout 20 seconds then went to rev it, it reved but sounded like it was running on 3 cylenders!? maybe a clogged cat?.............

Posted by on

  • dan Jun 29, 2009

    new plugs, coil on plug hemi motor design, al coils test fine, i have a more detailed post befor this one, still lost, all basics have been covered though, light a match maybe!!! lol

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Check plugs and wires first.

Posted on Jun 29, 2009

  • Philip Long
    Philip Long Jun 29, 2009

    Check your getting the right amount of fuel .Change the fuel filer.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Ford F150 would suddenly loose power and only idle. Pull over shut off sit a couple minutes crank and run fine for a while then do same thing again. Wrench would show up on instrument panel


Sounds like the catalytic converter or muffler maybe getting plugged up and the computer is putting the truck in limp home mode. Did you put a scanner on the truck. You might try to remove the 02 sensor ahead of the cat and see if it runs a little better it will not be perfect but should stay running if so do an exhaust check. When the cat or muffler gets plugged it puts back pressure on the engine and won't allow the fuel to be pulled into the engine properly.

May 19, 2017 | Ford Cars & Trucks

1 Answer

Real up and reving in park fast idle in drive


motor revving - CarGurus

www.cargurus.com > Questions > Chrysler > Town & Country

CarGurusDec 28, 2012 - motor revving - Sometimes the motor revves up and the light go dim on... If in park it takes alot of rev. to make the pop sound. ... 1996 chrysler cirrus change a bad fuel injector and now the engine revs ... Used Nissan Quest".

Idle issues... cold runs great... after warms up it hesitates ...

forums.nicoclub.com/idle-issues-cold-runs-great-after-warms-up-it-hesita...
Feb 20, 2009 - TYC 800107P Nissan Altima Replacement Cabin Air Filter ... when i go to park the car and throw it in park it goes up to like about .... If I leave it in drive when the idling starts to hesitate it tends to make the car jump forward.

All Questions and Answers for Nissan Repair - AllExperts.com

en.allexperts.com > Autos > Auto Repair

Jan 13, 2016 | 1996 Nissan Quest

1 Answer

Hi idle after changing sparks plugs


start by checking for a lose vacuum line that is what it sounds like to me u may have pulled one lose and not have seen that u did

Dec 24, 2013 | 1997 Mitsubishi Montero Sport

1 Answer

Air conditioner quits when idle and car revs


Is the radiator fan running when the ac is on ?

Jul 21, 2013 | 2002 Mercury Cougar

1 Answer

Engine is reving while idling


I think you mean 3000 RPM right? Or are you talking about your idle, even still 300 cant be. Let me know...

Nov 25, 2011 | 2000 Mercury Sable

2 Answers

1990 Chevy Scottsdale 1500 wont idle when first starting cold


ICM idle control module, loc throttle body, it may be dirty, remove clean or replace, its easy..

Jul 29, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

1987 MAZDA RX7


1. im not sure what the ATF trick is 2. yes that is correct 3. no theres a few different things it could be. it most certanly could be though. it doesnt take long for a rotary engine to get messed up if its sitting. take it to a mechanic to get a compresion test that will help you determine whats up.

Feb 08, 2009 | 1987 Mazda RX-7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...