Question about 2000 Chevrolet Silverado 1500

1 Answer

Do i remove serpintine belt carefully ? - 2000 Chevrolet Silverado 1500

Posted by on

  • danatrueblue Jun 29, 2009

    Hey thx 4 your answer . I dont need 2 worry about timiming marks on camshaft or crank or dont move engine & all is ok?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Yes you should alway be careful when removing belts and hoses as a mistake can cost you fans and radiators easily. First look for the belt tensioner. It will be a spooled item that presses against the belt tightening it by spring pressure. May a note of the route the belt takes and always put the new belt on the same way. The tensioner pulley may spring down a fair ways after you release it with the belt off. Just be sure you can still get at the tensioner at the right angle for putting the belt back on. whenthe belt is off make sure all pulleys and bearing are good and sound making no noise or vibration. If they do change them now and save a headache later.

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Serpintine belt


Here's video for the same job on a 1999 Grand Am.

utube.png You-Tube video "H3cnhfowLGA" placeholder (do not delete) utube.png


Nearly all the steps are the same - including jacking the engine & removing the mount bolts. You can skip the part about changing the tensioner pulley if you are not replacing it.
I hope this helps!

Nov 29, 2012 | 2001 Pontiac Grand Am SE

1 Answer

Cant put serpintine belt on


You don't take anything off

You just put a long 1/2" ratchet in the hole on
the tensioner & Pull against the spring tension until
you have the belt over the final pulley

Oct 12, 2012 | 2000 Buick LeSabre

1 Answer

Sterring noise i changed the pump but the noise still there


given you have replaced this pump and it is assumed to be new, your 2005 has a serpintine belt set up so isolation via removal of belt per unit makes noise solving troublesome. It is possible to use a mechanics stethoscope to isolate your noise, but these are hard to come by, accepting no responsibility here for advise followed for injuries or damage,,,you can if, " VERY very careful" do the same thing with a long wooden dowel placed on the suspect unit AWAY from the moveing belt pully/wheel, and then on the area of your ear that is closest to the hing of your jaw, you will hear it if that is the problem,, sometimes with the serpintine system thee ideler's and the belt tension idlers that you use to remove and replace the belt have worn bearings in them creating audible sounds that seem to come from the power steering. One other suspect is a worn brush set in your alternator to commutator running in a worn track on the commutaor. If you Know it's the Power steering pump drain/ and remove and return for replacement.

Aug 12, 2011 | 2005 Dodge Dakota

1 Answer

How to remove serpintine belt


Release the belt tensioner and the belt will virtually fall off the pulleys. Make a sketch of the route of the belt before you do that as it can become confusing when you try refit the new belt.

Feb 16, 2011 | Ford Futura Cars & Trucks

1 Answer

I need an exploded view of water pump replacement


Not too difficult of fix. You'll need to remove the serpintine belt. Drain the radiator. Remove the pulley from the water pump ( I believe three 10MM bolts) After removing this pulley you'll have access to all of the bolts holding in the water pump (I believe there are 5 or 6 8MM bolts) Reverse on install. No need to over tighten on the replacement pump as it has an o-ring seal. Take special care in reinstalling the serpintine belt. I'd get a bit of help to help hold the belt in place as you go.

I hope this may have assisted you, please let me know.

Thanks,
Tom

Apr 18, 2010 | 1996 Plymouth Voyager

1 Answer

Alternator


First you need to remove the serpintine belt or alternator belt. If it is a serpintine locate the tension pully(the one that doesn't look like it does anything) place a wrench over the pully bolt and pull while removing the belt. Most generaly all alternators have two bolts holding them in. Remove both bolts. and remove alternator on some vehicles you need to remove the top engine mounts to remove the acctual alternator. make sure you if you do this you put a jack under the bngine block. NEVER ON THE OIL PAN. After that simply remove the old alternator and replace it with the new one reinstall the serpintine belt as instructed on either the underside of your hood or where the hood latch is.

Apr 10, 2010 | 1993 Toyota Corolla

1 Answer

Fans don't work after relacing serpintine belt.


look around the wiring and sensors when belt broke some debris may have damaged or disconnected the circuit

Feb 14, 2010 | 1993 Buick Park Avenue

1 Answer

Need to replace old serpintine belt how do I relieve the tension


On belt tensioner pulley fit a wrench on the bolt that holds pulley, turn clockwise to release tension, hold and remove belt.

Jan 04, 2010 | 2003 Oldsmobile Alero

1 Answer

Need to replace serpentine belt on my cadillac sedan deville need the diagram.


dia gram should be located on the inside of the hood when open or on the top front of engine look care fully its the not hard to find and make sure you have a gm serpintine belt removal tool

Jul 22, 2009 | 1998 Cadillac DeVille

1 Answer

Serpintine belt replacement


There is a pulley that appears to be not operating anything. This is an idler pulley, Attach a socket to the center of the pulley, when apply pressure it will turn releasing pressure on the belt, remove belt paying attention to the route. Replace belt as it came off. You will be fine.

Jul 05, 2009 | Saturn SC1 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...