Question about 2004 Chrysler Crossfire

1 Answer

My 2004 Chrysler Crossfire will not start

The problem started a couple of month's ago. It would crank but no start. It would start up and idle rough with no throttle response and then die. This would happen repeatedly. Slammed the hood one time and it started. Next time I left it for a couple of hours then it started. Now it won't do anything. Now it just cranks.

Posted by on

  • rozman63 Jul 01, 2009

    JUST HAD MY PROBLEM REPAIRED. TURNS OUT THAT THE FUEL PUMP RELAY GOING OUT IS A COMMON PROBLEM IN THESE CARS. GOOD LUCK WITH YOUR CROSSFIRE.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Change the crankshaft sensor.

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would make a 2004 Chrysler crossfire start but only idle a short time


Engine sensor , ignition control sensor ! Is the vehicle check engine light on ? Do you have a scan tool to check engine sensor data ? Do you have a DVOM - digital volt ohm meter ? any sensor that is powered by the PCM - engine computers five volt reference voltage circuit . 5 volt reference or crankshaft postion sensor . Doing testing is the way to find the problem .Check out videos on ignition system testing .

Feb 04, 2017 | 2004 Chrysler Crossfire

1 Answer

At first the truck idles extremely rough when cold cranked. This went on for a couple of days, now the truck will not start at all. It hits every once in a while while repeated cranking on cold start. ...


Sometimes on cold days if the cranking amps on the battery are low, then it will be hard for the vehicle to start. Also, check the oil level. If the level is low it will create a hard start and rough idle for the vehicle.

Nov 27, 2010 | Ford F-250 Cars & Trucks

1 Answer

Just fueled up 93 octane. drove approx 1/2 mile to work. started the car, check engine light came on and runs extremely rough and stalls. could it be the fuel and how do i check it. 2004 chrysler...


I would suspect the fuel is the problem, most likely water is in the fuel, but get the codes read to see what fault shows up that turned on the check engine light.

Oct 14, 2010 | 2004 Chrysler Crossfire

1 Answer

My car wont start but all the lights and stuff come on it just wont crank or start whats the problem with my car??..2004 crysler crossfire


Check starter motor wires are connected and clean and tight.check the very thin wire at the starter is clean and tight.ALL WIRES ARE ON THE SOLINOID.

Jul 10, 2009 | 2004 Chrysler Crossfire

2 Answers

Cranks but wont start


this is a classic symptom of a defective fuel pump pressure check valve, it is not holding pressure after the car is turned off, this causes the problem you have, the check valve is part of the fuel pump and that is located in the gas tank.

Apr 09, 2009 | 2003 Honda Accord

1 Answer

2004 Chrysler Cross 48,000 miles


i have the same probem for the last 6 months and the dealer CANNOT diagnose the problem....class act lawsuit is the way i'm headed...

Feb 27, 2009 | 2004 Chrysler Crossfire

1 Answer

1993 altima will crank but will not start..


replace the distributor oil is leaking into the electronics of the distributor and shorting out pull cap back off and look and see if oil is leaking out

Jan 24, 2009 | 1993 Nissan Altima

4 Answers

04 Crossfire not starting


Same thing happened to me. It was giving me problems starting it. It died on me at the stop sign last week. I kept driving. On Friday it shut down on me while doing 60mph on the hwy. I towed it to the nearest dealer. The said they had top replace the cranck sensor and a cam sensor. I paid $1,043.01 for that. Today I couldn't start it....

Sep 20, 2008 | 2004 Chrysler Crossfire

Not finding what you are looking for?
2004 Chrysler Crossfire Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...