Question about 2007 Ford Expedition EL XLT

1 Answer

Trying to find wire for reverse light - 2007 Ford Expedition EL XLT

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,822 Answers

Replace the reverse switch at the transmission.

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 Chevy Uplander and I'm trying to connect a reverse backup camera to my car and I do not know which wire is positive for the reverse light bulb


open up the rear bulb compartment cover
and note the color wires running into the reverse light bulb holder

a hand full of fuses as you
use a LED test light or voltmeter to find the right wire

and use those color wires as your power /earth for the reverse camera

or you need the rear loom wiring diagram for that 2006 chev

Oct 13, 2016 | Cars & Trucks

1 Answer

Reverse lights stuck on my 2005 Toyota prado when in drive


there is a sensor on the right side of the main gearbox.
Disconnecting the wires the reverse lights should be off...
If not try check wire harness...

Greetings - Claudio

Feb 11, 2015 | 2005 Toyota LandCruiser Prado

1 Answer

Why does my 95 chevy 4x4 diesel keep blowing fuses when i put it in reverse


You can rule out internal transmission wires. The only thing I know of would be the reverse light wiring. You have one power wire to the neutral switch. So when the lights are supposed to come on the fuse blows the turn signal . You said you check the wiring, Did you check for continuity? High resistance cause a higher amperage draw. Also did you check the hot wire for short to ground? Try leaving the engine off. No lights on. Put it in reverse, see what lights come on. Have someone stand in back and watch as you put it in reverse. The lights should flash for a split second before the fuse blows. If any other lights come on, you have lost ground to the reverse lights.


25349764-hyer52qe2lvlylkatonhnc1i-2-2.gif

Jan 01, 2015 | Cars & Trucks

2 Answers

Reversing lights not working


It may be a bad back-up light switch on the transmission. Look for a two-wire connector on the transmission or transaxle, although it may be included in a wiring harness for the transaxle. If you find the two wires for the reverse light switch, you can jumper the two wires together, and with key on, the reverse lights should be on, verifying a bad reverse light switch. Screw it out and replace. But if still no lights, there may be a wiring break or a wiring problem going to the lights.
Good luck.

Mar 23, 2012 | Cars & Trucks

1 Answer

Only one reverse light goes on on my 2007 VW Passet, how do I fix?


if you have already tried changing the bulb and still not working than the simplest way is to run a wire from the working bulb to the other side saves time trying to unravel all the harness's first you will need to find wich of the two wires is not doing its job the power wire or the ground wire? test light will help you with that, with engine off put your car in reverse turn the ignition to on that will turn on the working reverse light use a test light to find the problem go to the none working light remove the bulb using the test light touch each connection point to see if any light up the test light if not then you have a bad power supply, but if it does light up then you have a bad ground wire in either case you can jump the working light to fix the light if ground is bad jump the ground and vise versa.......

Nov 14, 2010 | 2007 Volkswagen Passat Sedan

1 Answer

Reverse ligtht not work


Look underneath ur vehicle, look at the transmission, notice that a wire connected to a SWiTCH, that is ur reverse light switch! Check if the wire is still connected to the switch, if it is connected try to short it and turn ur ignition to "ON", reverse light should be lighted ! If not, check the fuse! If LiGHTED, ur reverse switch is busted and needs to replace! U could do it by urself by using SPANNER/WRENCH! Taah!

Nov 10, 2010 | Dodge Pickup Cars & Trucks

1 Answer

Wiring 4 way flat trailer plug. brown wire running


you got brown for running parking light
green for right turn/stop
yellow for left turn/stop
white for ground
reverse lights are only wired on a 6 or 7 plug connector
make sure you on the dark green for right turn stop not the light green
the light green is for reverse

Jun 24, 2010 | 1999 Chevrolet Tahoe

1 Answer

My reverse lights dont work


On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

Apr 12, 2009 | 2002 Mitsubishi Lancer

2 Answers

2000 toyota camry check engine light. trac light on. when i step on breaks reverse square indicator on dash board goes on. No reverse lights and rear light indicator on.


wires are pinched and shorting together near the left (drivers side) trunk hinge. brake light power is feeding back through the reverse light wiring. this will also turn on the check engine light with a neutral safety switch malfunction code as the computer also sees this voltage in the reverse light circuit. Find and repair the wiring, pull the EFI fuse in the panel under the hood to clear the code. Hope this helps

Dec 27, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
2007 Ford Expedition EL XLT Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...