Question about 1990 Honda Accord

1 Answer

I can't find directions on line to change the driver's side headlight out of the headlight assembly. I took the assembly out of the car, not a simple task, you have to remove the bumper, but I can't figure out how to remove/reinstall the headlight itself

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

If I can remember, there should be two small screws on the bottom left of the headlight. This is the spring load. remove the screws and also remove the two small screws on the upper right. this will help remove the adjusting screw. the installation is in reverse.

Posted on Jun 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How How do i change the headlight bulb on the drivers side of my 2007 Hyundai Entourage?


You have to take the black plastic top off under the hood on the front.....than you take the whole headlight out, I believe it's only two bolts...there is opening for each light and they are pretty simple to change.

Jul 04, 2014 | 2007 Hyundai Entourage Limited Minivan

1 Answer

Dim headlight one side


Check voltage to lamp assembly. Could be a relay, a bad wire, or a bad connector. Since one headlamp works correctly, the switch assembly probably works. Without a wiring diagram. I can't tell whether the headlights get power directly from the switch or not... Time to buy a manual.

Apr 01, 2014 | Chevrolet Equinox Cars & Trucks

1 Answer

Drivers side headlight bulb replacement


  1. Open the hood to the 1999 Dodge Stratus.

  2. Locate the two headlight lens assembly retaining screws at the top of each side of the assembly.
  3. Remove each screw with the ratchet and a suitable socket.
  4. Place the screwdriver behind the lens assembly to assist in prying out the guide pins that secure and align the headlight assembly. Hold the lens assembly from the outside edge (marker light/directional light section) first and pry from behind with the screwdriver to unseat the guide pins. Pry from the inside end of the lens assembly to unseat the other guide pin.
  5. Pull the lens assembly out far enough to reach behind it and disconnect the headlight bulb wire harness from the back of the bulb. Or simply remove the bulb by twisting the harness and retaining ring counterclockwise and remove it as an assembly.
  6. Turn the marker light/directional light socket and wire counterclockwise to remove it from the headlight lens assembly.
  7. Remove the assembly from the front of the Stratus.

Feb 28, 2011 | 1999 Dodge Stratus

1 Answer

How do i change a headlight


1.FACE THE VEHICLE SO THAT BATTERY IS ON YOUR RIGHT;

2. REMOVE THE BLACK PLASTIC PIECE THAT RUNS OVER RADIATOR BETWEEN HOOD LATCH AND FAN. IT IS ABOUT 53 1/2" LONG AND HOLDS THE HOOD PROP CLIP. (3 PLASTIC PUSH RETAINERS & 2 SHEET METAL SCREWS);

3. REMOVE THE GRILL ASSEMBLY UNDERNEATH THE PIECE IN STEP 2 BY PUSHING DOWN FIRMLY ON 4 RETAINER CLIPS WHICH RUN ALONG THE TOP. USE A WIDE SLOT SCREWDRIVER. PULL UP GENTLY ON GRILL ASSEMBLY. IT WILL POP OUT. THE GRILL ASSEMBLY EXTENDS UNDER EACH HEADLIGHT ASSEMBLY (HA) AND IT DISPLAYS THE CHEVROLET LOGO IN THE MIDDLE. MY GRILL ASSEMBLY POPPED OUT EASILY AND ALL THE OTHER RETAINER CLIPS ON THE BOTTOM AND BENEATH AND TO THE SIDE OF HA WERE AUTOMATICALLY RELEASED WITHOUT ANY FUSS;

4. ON TOP OF HA SEE ONE TAB (ABOUT 1" LONG)ON THE RIGHT SIDE AND ONE ON THE LEFT (THE ONE ON L IS CLOSER TO THE FENDER);

5. PULL UPWARD DIRECTION ON TABS. THEY WILL SLIDE UPWARD A COUPLE OF INCHES AND WILL RELEASE THE HA WHICH YOU CAN THEN PULL OUT TOWARDS YOU;

6.AT BACK OF THE HA, REMOVE 2 ROUND RUBBER CAPS (ABOUT 4" IN DIAMETER)--ONE FOR LOW BEAM--ONE FOR HIGH. REVEAL BULBS. UNSNAP THE WIRE HARNESS FROM BULB BASE AND TURN BULB 1/4 TURN CLOCKWISE (REMEMBER YOU ARE FACING THE TRUCK)

7.REPLACE BULB(S). #9006 BULB IS GRAY-BASE, FOR HIGH BEAM ON OUTSIDE. #9005 IS BLACK-BASE, LOW BEAM TO INSIDE OF HIGH BEAM.

CHANGING HIGH AND LOW AND REASSEMBLY TOOK ABOUT HALF HOUR. GOOD LUCK.

ALTERNATIVE:
IF YOU ARE REPLACING THE PASSENGERSIDE HEADLIGHT JUST REMOVE THE AIR FILTER COVER AND PULL PLUG OUR FROM BEHIND HEADLIGHT AND REPLACE. BE CAREFUL HANDLING LIGHT BULB.
TO CHANGE THE ONE ON THE DRIVER'S SIDE JUST REACH IN FRONT OF THE BATTERY TO ACCESS THE PLUG AND HEADLILGHT. TOOK ABOUT 5 MINUTES. ENJOY YOU TRAILBLAZER, GREAT TRUCK.
Thank you for using fixya

Jun 12, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

Lightbulb driver side 2008gmc 3500 6.6l


how to change driver side headlight bulbs?

May 30, 2009 | 2008 GMC Sierra 3500HD 2WD

1 Answer

97 ford escort headlight adjustment


It should be easy their is a torx screw in two different place on the to at the rear of headlight that you can adjust

Jan 25, 2009 | 1997 Ford Escort

1 Answer

How do you change the headlight on 97 buick Lasabre.


If you Google that, Im sure that you can find a set of directions on how to do. It is usually very simple. JOhn...

Jan 10, 2009 | 1997 Buick LeSabre

1 Answer

Headlight


There is a round 3 inch rubber cap directly behind the bulb assembly. Pull it off with your hand or pry it with a screw driver. With that cover off you can reach in and turn the bulb assembly counter clockwise a 1/4 turn then it pops rite out. There is a white clip on the bulb assembly that must be undone to remove the bulb. Re install in reverse order.

Nov 18, 2008 | 2003 Chevrolet Trailblazer Ext

1 Answer

How do you change the drivers side headlight assembly?


You need to remove the bumper assembly to remove the headlight.

Oct 14, 2008 | 2003 Nissan Altima

4 Answers

Remove headlight assembly


there is a nut on the left side of the light on drivers side,just the opposite on passenger side. you will need a deep socket. there are 2 10mm bolts on top of the assy. and on the back is a 10mm nut you will have to remove on order to remove the assy.

May 15, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
1990 Honda Accord Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...