Question about 2005 Chevrolet Tahoe

1 Answer

Instructions to replace the backlight on steering wheel controls

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

You can't. they are built into it as a whole unit. You need to find a good one or buy a new one from the dealer.

Posted on Jun 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse to change for steering wheel lights and gear shifter lights 2010 ford edge


It's not a fuse , the SJB - smart junction box controls these lights ! This is fords body control module . If the Heater / A/C control panel ,hazard switch ,headlamp switch , message center switch all work, it is not a fuse . The gear shifter I would say the bulb is burnt out . The steering wheel lights could be out because of an open in the clock spring . The clock spring is a device inside the steering column under the steering wheel that keeps your horn , cruise control , radio buttons etc... connected electrically . How cars clock spring works

Feb 04, 2016 | 2010 Ford Edge

1 Answer

How to remove an SIR coil on 97 Deville/Technical drawing of steering column?


The clock spring assembly was most likely damaged during removal/assembly of the repairs. This assembly controls the airbag/horn/steering wheel functions. It is not that hard to change if you have a steering wheel puller to get the steering wheel off. Here is an exploded diagram. Hope it helps. The very top of the diagram is the clock spring assembly and it will be the first thing you see when the steering wheel is removed

remove-sir-coil-97-deville-technical-2weuas4jkbrvbhrwhonxf50x-2-0.gif

Nov 11, 2015 | 1997 Cadillac DeVille

1 Answer

Replaced intermediate steering shaft, 2007 Chevy HHR. steering wheel mow crackling, clicking when I turn it, airbag light on. steering wheel computer controls not responding. Someone said coil spring?


That would be clock spring. When the itermediate shaft was disconnected the wheel was apparently allowed to turn, and when the steering was re-connected the clock spring was too far turned one direction. You will have to have the wheels turned straight ahead when you install the new one or this will happen again. The new one will come with installation instructions, be sure to follow them.

Jun 11, 2015 | Cars & Trucks

1 Answer

Turn indicator/wiper switch assembly replacement instructions please?


steps required to remove and replace indicator switch assembly.
1.disconnect the battery earth lead.
2.from the rear of the steering wheel remove the screws retaining the horn pad..
3.lift the horn assembly away from the steering wheel far enough to remove wiring.
4.Once that is done then move to the next step.
5.Remove the locknut and steering wheel nut .
6.then mark the end of the steering shaft and the steering wheel to correctly relocate and install in same position.
7.then with the correct tool remove the steering wheel from shaft.
8.then once the steering wheel is removed you can then move on to removing the lower steering column cover screw and then remove cover.
9.disconnect the wiring from the multi point connector under instrument panel.
10.release and free wiring harness.
11.unscrew and remove the hazard switch knob.
12.remove the dipper-wiper switch securing screw and manoeurve the switch upwards.guiding the wiring through the column.
13.you will actual find there are 3 phillip head screws securing the switch to lever switch to the combination switch.

14.when putting this assembly back to together just follow these steps in reverse..
hope you find this helps you

Aug 03, 2012 | Holden VK Cars & Trucks

1 Answer

How to remove terrain air bag


How To: Remove your air bag & steering wheel
1. With the car running turn you steering wheel so that the button controls on the wheel are at 12 o'clock and 6 o'clock.
2. Turn off the car.
3. Remove the Air Bag fuse #8 from under the back seat, and disconnect the negative battery terminal. Let the car sit for at least 15 minutes
4. Using a flat bladed screw driver insert and twist about 90* while pulling out on one corner that corner of the airbag.
5. Remove all electrical connectors on the back of the airbag and your two steering wheel control buttons. there are a total of 6 connections to be removed.
6. If you only need to replace your steering wheel control buttons you will see two Torx screws on the back side of each control, unscrew and replace the unit and you are done! (after you reconnect everything).
7. To continue on with removing the steering wheel reach for your 21mm socket, and remove the nut.
8. Using a steering wheel puller that has "hooks" at the ends, follow the instructions with your kit to remove the steering wheel
9. Once the wheel is off and you go to re-install, make sure you have it lined up correctly. The steering wheel nut is tightened to 35 foot lbs.

Oct 16, 2011 | 2010 GMC Terrain

1 Answer

I have a 2002 Yukon Denali and I was wanted to know, how do u change the bulb in the steering wheel?


Steering Wheel Control Switch Assembly Replacement Removal Procedure
  1. Remove the steering wheel. Refer to Steering Wheel Replacement .
    399638.gif
    tif.gif
  2. Remove the horn switch from the steering wheel.
    755486.gif
    tif.gif
  3. Remove the steering wheel shroud retaining screws from the back of the steering wheel.
  4. Remove the steering wheel shroud from the steering wheel.
    408596.gif
    tif.gif
  5. Remove the steering wheel control switch mounting screws.
    780085.gif
    tif.gif
  6. Disconnect the steering wheel control switch (2) electrical connector (1).
    408598.gif
    tif.gif
  7. Remove the steering wheel control switch from the steering wheel.

Steering Wheel Replacement Tools Required J 1859-A Steering Wheel Puller
Removal Procedure
  1. Disable the supplemental inflatable restraint (SIR) system. Refer to Disabling the SIR System in SIR.
  2. Remove the inflator module. Refer to Inflatable Restraint Steering Wheel Module Replacement in SIR.
  3. Remove the horn switch. Refer to Horn Switch Replacement - On Vehicle .
  4. Make an alignment mark in order to note the relationship of the steering wheel to the steering shaft.
  5. Remove the steering wheel nut.
    374820.gif
    tif.gif
  6. Remove the steering wheel, using the J 1859-A .
Installation Procedure

Oct 04, 2010 | 1995 GMC Yukon

1 Answer

Ok i need to know how to assemble the steering wheel


Steering Wheel Removal & Installation Special Service Tools (SST) Required:
  • J1859-A Steering Wheel Puller
  • J42578 Steering Wheel Puller Legs
To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Place the ignition into the OFF position.
  3. Perform the SIR System Disabling procedure.
  4. Remove the inflator module
  5. Scribe an alignment mark onto the steering wheel hub in line with the mark on the steering shaft.
  6. Loosen the steering wheel nut.
  7. Position the steering wheel nut flush with the end of the steering column shaft.
  8. Loosen the steering wheel using the J1859-A SST.
  9. Remove or disconnect the following:
    • The steering wheel controls electrical connector (if equipped)
    • The horn switch lead from the steering hub
    • The steering wheel nut
    • The steering wheel from the steering shaft
    • The steering wheel controls and the steering wheel controls harness from the steering wheel (if equipped)
To Install:
  1. Install or connect the following:
    • The steering wheel controls and the steering wheel controls harness to the steering wheel (if equipped)
    • The SIR connector properly routed through the steering wheel
    • The mark on the steering wheel with the mark on the steering shaft
    • The steering wheel CAUTION
      The fastener is prevailing torque type and may only be reused if the fastener and its counterpart are clean and free from rust and the fastener develops 27 inch lbs. (3 Nm) of torque or drag against its counterpart prior to the fastener seating. If the fastener does not meet these criteria it must be replaced.
    • The steering wheel nut
      1. Torque to: 33 ft. lbs. (45 Nm)
    • The horn switch lead to the steering hub
    • The steering wheel controls electrical connector (if equipped)
    • The inflator module
    • Enable the SIR system.
  2. Ensure that the steering Wheel controls operate properly (if equipped).
  3. Ensure proper horn operation.
prev.gif next.gif

Jul 03, 2010 | 1997 Chevrolet Venture

2 Answers

The controls on the steering wheel stopped working and the radio doesnt work either


Replace the clock spring under steering wheel, if applicable to your vehicle

May 06, 2010 | 1995 Buick Riviera

1 Answer

When driving at night, not all the lights on the steering wheel, cruise control, and radio illuminate. Fuses? How do I know which one?


These steering wheel lights are usually sealed units, much like radio backlights. They can be repaired, but they have to be sent out for service, which means removal of the steering wheel, etc.
Speak to your dealer about the cost of such a service, your options, and their recommendations.

Jul 19, 2009 | 2005 GMC Sierra 2500HD 4WD

Not finding what you are looking for?
2005 Chevrolet Tahoe Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...