Question about 1999 Chevrolet Silverado 1500

Open Question

How do you remove a door panel on a 1990 chvorlet silverado?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rick_amick
  • 69 Answers

SOURCE: door panel removal

The book says 1. remove panel pull strap 2. remove door handle bezel 3. on 1995-2001 models,remove power accesory panel and trim panel upper extension. 4. remove armrest screws and pad. 5. remove window handle,I guess if not power windows.
KD makes a tool to go in between door panel and door to pop the door clips loose. KD 3705
You will also have to have a window crank tool if it is manual window. KD431
Hope that will help.

Posted on Mar 23, 2009

c17hydro
  • 2984 Answers

SOURCE: need to remove left rear door panel

  1. If equipped, remove the window crank handle by using a retaining clip removal tool.
  2. Remove the door handle bezel by inserting a flat trim removal tool between the door panel and handle bezel to release the locking tabs.
  3. Remove all door panel electrical connectors .
  4. Remove the door panel push pins and trim screws. Lift the door panel up and out to release the door panel locking tabs.

Posted on May 22, 2009

  • 1986 Answers

SOURCE: 1990 trofeo door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 34 Answers

SOURCE: door panel removal 1999 silverado

The door panels are held on with plastic clips. Chances are a few of the clips will break, but they are not expensive or hard to replace. You can buy a tool from one of your local parts store that slides under the head of the retainer and helps to remove it, but many people do not use them. There are several retainers around the edge of the panel.

Posted on Sep 28, 2009

  • 1 Answer

SOURCE: need to remove inside door panel on drivers side

just pop out the triangle piece from the top at the top front of the door panel with a flat head screwdriver. Then simply pop out the door lock cover from the aft side and the door handle cover from the aft side as well. Then pop up your cap containing the auto door locks and windows and disconnect the cannon plugs. Then just remove 2 screws (1 from under the door lock/window cap and one just insde the door handle itself. You'll then life up and towards you to remove the panel. Don't pull it too far out because you'll still need to disconnect the speaker cannon plug and pull out the door open light at the bottom aft of the panel. You can then set the door panel off to the side.

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I purchased a replacement side view mirror for a 2010 Silverado. I need to remove the door panel to get to the wiring connection How do I remove the door panel?


Try with this procedure...
1) Start with opening the driver's side door and lowering the window. Remove lock lever (1A).
2) Using a plastic pry bar [slotted screwdriver], slowly pry plastic cover to reveal screw.

CAUTION: These plastic covers are fragile and break easily. Be very gentle in disengaging them.

3) Remove screw with a 10mm socket.
4) Slowly pry plastic cover using a plastic pry bar [slotted screwdriver].
5) Remove the (2) revealed screws with a 10mm socket.
6) Pry off the door panel controller using a plastic pry bar. Disconnect wiring and remove the controller.
7) With the plastic pry bar, pry around the triangular panel as shown.
8) Lift up and slowly pull door panel out partially.
9) Release the door lever rod with a needle nose pliers. Remove and set door panel aside.

Keep us updated.

Jan 11, 2011 | 2009 Chevrolet Silverado 1500

1 Answer

How do I remove the driver's door panel on a chevy 2007 nbs?


open door pull ruber boot back on door side unplug wire connections snap lock release on con pull pins pull door

Jun 18, 2010 | 2007 Chevrolet Silverado Classic SS New...

1 Answer

How to remove door panel on 2002 Chev. silverado


remove window switch assembly. you will see a 7mm screw behind it remove that screw and one rt under grab handle. remove bezel around door handle and top panel that is triangle shaped by mirror. once all this is done just lift up on panel as it has hooks that hold it on.

Feb 18, 2010 | 2002 Chevrolet Silverado

1 Answer

Im trying to get the door panels off my 1999 chevrolet silverado


There are a few screws which need to be removed, one under the map compartment (bottom of door ) one behind cover at door handle, once these are removed pry door panel out from the bottom up removing it from the clips, once this is complete lift up and remove entire panels off lip at top

Oct 24, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Need to remove the door panel off a 2001 chevy silverado


Start by removing the insert located at the door handle. It should come out using a screw driver. Pry up thw eindow control unit and remove, locate the screws should be one at the door handle and two at the bottom. Pry up on the panel and pull toward you. If the panel will not pull up look for some more screws.

Sep 10, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

How do i fix loose drive side side mirror on a 1990 Chevy silverado 1500?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Jun 29, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Need to remove left rear door panel


  1. If equipped, remove the window crank handle by using a retaining clip removal tool.
  2. Remove the door handle bezel by inserting a flat trim removal tool between the door panel and handle bezel to release the locking tabs.
  3. Remove all door panel electrical connectors .
  4. Remove the door panel push pins and trim screws. Lift the door panel up and out to release the door panel locking tabs.

May 22, 2009 | 2006 Chevrolet Silverado

1 Answer

Door panel removal


The book says 1. remove panel pull strap 2. remove door handle bezel 3. on 1995-2001 models,remove power accesory panel and trim panel upper extension. 4. remove armrest screws and pad. 5. remove window handle,I guess if not power windows.
KD makes a tool to go in between door panel and door to pop the door clips loose. KD 3705
You will also have to have a window crank tool if it is manual window. KD431
Hope that will help.

Mar 23, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Remove door panel


Remove the screws and lift up. There aren't any screws behind the window switch, it is screwed on from behind. There is a hidden screw behind the lock slider.

Mar 01, 2009 | 2000 Chevrolet Silverado

1 Answer

1990 trofeo door panel removal


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Feb 19, 2009 | 1990 Oldsmobile Toronado

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...