Question about 1994 Cadillac Seville

1 Answer

Whats is tourqe for the lifter bolts

Whats is tourqe for the lifter bolts

Posted by on

  • raymondruiz7 Jun 28, 2009

    I'm sorry Rocker arm bolts



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers

This vehicle uses hydraulic "lifters" and dual overhead cams, so "lifter bolts" doesn't compute. Can you rephrase what you're looking for?

Posted on Jun 28, 2009

  • RBStorms Jun 29, 2009

    I'm sorry to give you the run-around, but according to the data I can find on this engine, there are no specs for tightening the "Rocker Arm" bolts... The Cam Bearing bolts should be tightened to 150 INCH/LBS. Note that is NOT the same as Foot/Lbs. :)



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the tourqe specs on the intake on a1996 bmw 318 ti

The 6 mm bolts are 10 Nm
The 7 mm bolts are 15 Nm
The 8 mm bolts are 22 Nm

Mar 03, 2015 | BMW Cars & Trucks

1 Answer

What is the tourqe required on front strut

the top bolts on the strut mount are not much.about 30 ft lb.the 2 main bolts are about 80 foot lb.most techs i have worked with hold the bolt head with a wrench and put the nut on with an impact wrench.

Feb 23, 2015 | 2000 Dodge Intrepid

1 Answer

Tourqe converter bolts wont line up

They have a slight offset pattern whereas the main bolt has to be installed, loose to allow adjustment line up for the other bolts. Good luck.

Dec 25, 2013 | 1991 Plymouth Grand Voyager

1 Answer

Need head bolts tourqe sequence for a 89 tercel

1989 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence809142031993 L4 headbolt sequence:
Cylinder Head Bolt Torque Sequence80914199they appear to be the same,other than the torque angle. good luck!

Oct 20, 2011 | 1993 Toyota Tercel

1 Answer

What is the tourqe? vaccum leak at intake

Torque, also called moment or moment of force is the tendency of aforce to rotate an object about an axis,[1] fulcrum, or pivot. Just as a force is a push or a pull, a torque can be thought of as a twist.

Loosely speaking, torque is a measure of the turning force on an object such as a bolt or a flywheel. For example, pushing or pulling the handle of a wrench connected to a nut or bolt produces a torque (turning force) that loosens or tightens the nut or bolt.

Vacuum leaks in manifold means u got a broken VACUUM hose that helps your HYDRAVAC to boost ur BRAKiNG power! Just look at ur BRAKE MASTER and u will see at the rear, there is this BiG ROUND drum, hose/pipe is attached to it, follow that hose/pipe it will lead u to the iNTAKE MANiFOLD, where air/fuel was being sucked by the ENGINE PiSTON!

Nov 09, 2010 | 2001 Jaguar S-Type

1 Answer

If I'm installing headers on my 03 silverado is there anything else to consider after I install them like reprograming or anything to make sure it runs ok or can I just throw them on and call it a day?

buy gaskets deffinatly. but no, no reprogramming required. However i do suggest a SUPER CHIP, its a piggy back tool that remaps the fuel and air intake for modified trucks to save MPG and/or increase Horsepower and Tourqe. If you are just installing headers, make sure to tighten the bolts going from the middle of the exhaust manifold(headers) outwords, keeping the tourqe the same on each bolt. otherwise you could lose compression and send a piston flying through your block.

Oct 04, 2010 | 2003 Chevrolet Silverado 1500

1 Answer

Im replacing the head gasket what is the tourq and sequence for instillation

A torque specification is how tight you must make the bolt by using a torque wrench which measures the tightness you apply to the bolt, ensure you are using new head bolts, a reliable torque wrench, clean the threads of the cylinder head (with tap) where head bolts screw into and when installing bolts ensure they are properly lubricated. And the sequence is the order in which you tighten each bolt.

Jun 19, 2010 | 1996 Acura TL Series

1 Answer

Head tourqe specs for 403 olds and bolt tightening

Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)


Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

2 Answers

Just replaced head gaskets and now it cranks over like no compression

how badly was this truck overheated? you may have collashed the rings and pistons, this would give near to zero compression

Oct 28, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
1994 Cadillac Seville Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides