Question about 2005 Mitsubishi Galant

1 Answer

How to remove rotar? Do the two small screws in the face of the rotar need to be removed?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Yes they do

Posted on Jun 29, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I set the distributor timing on the golf mark1 fuel injection?

take out the spark plug neares the belt pulleys then turn crankshaft till the car is on compression stroke jut at top dead center stop it at top check to be certain on top after compression the number one plug tower on the distributor will be were the rotar is to be positioned with the distibutor case placed in the normal way it was befor it was removed rotar faceing the number one distributor wire closest to motor on top of distributor right clockwise 1342


Feb 06, 2018 | Volkswagen Golf Cars & Trucks

1 Answer

How do I remove front rotors

Hi Richard remove the wheels brake calliper s and mounting brackets then if there is grub screws holding the rotars remove them then get a big hammer and remove thd rotars they get atuck with rust so don't be shy with the hammer. Regards Jim...

Jun 06, 2015 | 2006 Jeep Grand Cherokee

1 Answer

How to get off rear brake rotar

remove the wheel, remove the caliper,check the other wheels .put the hand brake off .remove the screw holding on the rotor ,and pull off.

Mar 23, 2013 | 1995 Jeep Grand Cherokee

1 Answer

How do I remove the cover to replace the ignition switch on my 2001 Porsche Boxster?

hello there
are you replacing only the electrical part?
If yes ,you just need to remove the air duck(plastic)pipe and with a help of a flash light and small flat screwdriver (very small) you can remove the (only a little bit) 2 little screws facing each other to remove the switch.


Feb 14, 2011 | 2001 Porsche Boxster

1 Answer

What do I need to get the rotars off

There should be two phillips head screws in each rotor. They can be stubborn to get out. I use a manual impact screwdriver on mine and they come out fairly easy. After the screws are out, they should pop off. If not, a couple of taps with a rubber mallet will usually do the trick.

I am assuming that you have removed the caliper already?

Jul 13, 2010 | 1995 Honda Accord

1 Answer

Removing front rotar

rotar doesn't contain the studs, the plate/hub behind the rotar does - you need a 32mm socket to undo the axle nut to then get at the hub (need a flat screw driver to lever the nut tang up first). If it's seized on put the rotar and wheel back on (leave the axle nut off) and gently rock it in a top-bottom motion (not radially or axially) to free it up. you can then gain access to the hub and studs. put the wheel nuts back on the studs 2 -3 turns so that you have a 'seat' and using a bolt with a smaller dia to punch them out

May 08, 2010 | 1991 Subaru Legacy

3 Answers

A dvd is stuck in my Chrysler town and country multi disk dvd/ cd player. How do I remove it?

Look around the face plate for a very small hole...use a straightened paperclip or equivalent and press in a few inches...its a manuel door release and you should gain access to at least the loading tray.

Apr 24, 2009 | 2005 Chrysler Town & Country

1 Answer

Help removing interior door panel/ 1996 Subaru Impreza Coupe

First you remove the small triangular shaped plastic piece that is on top of the door panel by the front of the door by the mirror by simply prying it of. Next behind the door open lever if there is a small plastic cover remove it under it will be a screw. Next your window switch will just pry up and out, disconnect the wiring, under the switch there will be a screw ataching the door panel to the door. Next on the face of the door panel if there is a small cover about the size of a nickle but elongated, remove the cover and remove the screw below it. Next pry the door panel from the bottom untill it "pops" out and grab it and pop the rest of the panel out, lift the panel up off of the window ledge.

Mar 22, 2009 | 1996 Subaru Impreza

1 Answer

How to get to brake light to replace bulb?

you need to pull it off opp. derection studs are facing ball and socket type fit...

Dec 30, 2008 | 1995 Toyota Corolla

1 Answer


Engine timing for 2f engine to put timing gear in order first remove the timing cover front crankshaft you can see two gears which is crankshaft and ather one cam-shaft. when you look front face of the gears you can see timing mark two dots.

put the first cylinder on top-dead center when the piston on that position next put the camshaft gear both marks must be in line,facing each ather.
next remove distributor cover have look rotar direction it must point first direction of first cylinder.if not remove the disrobutor and rotate your fingers to that directon contact point opening position.
start the engine ,jop done.
i thing it will help you.

sorry about my english wrating iam just leaning the language.

Sep 28, 2008 | 1983 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides