Question about 1998 Oldsmobile Intrigue

1 Answer

How do I clear the " change Oil" dash light after an oil change?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 109 Answers

  1. Turn the ignition to ON; do not start the engine.
  2. Fully depress and release the accelerator pedal slowly 3 times within 5 seconds.
  3. If the CHANGE OIL indicator flashes, the system is resetting.
  4. Turn the ignition to OFF after the indicator has finished flashing, then start the vehicle. If the CHANGE OIL indicator comes back on, the engine oil life monitor has not reset; repeat the procedure.

Posted on Jun 28, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: oil change light

Turn the key on. Observe the odometer. Is "ODO" displayed? If not, push the trip meter button until "ODO" is displayed, with the total mileage travelled shown.
Turn the key off.
Push & HOLD the trip reset button until advised to release it.
Turn the key to "ON" (do not start engine)
Observe the ODO display.
You should see 5 dashes, then 4, then 3, then 2, then one, and finally, five zeros.
The original mileage that you observed should be redisplayed.
Release the trip reset button.
The proceedure is now complete.

Posted on Sep 22, 2008

emissionwiz
  • 75817 Answers

SOURCE: 2006 Ford Explorer "Oil Change Required" light is still on after changing the oil

IF YOU FIND THIS INFO USEFUL PLEASE RATE ME AS A FIXYA! THANKS

Oil Change Reset
A press of the OIL CHANGE RESET switch will allow you to
reset the oil life feature to 100% (or your Personalized Oil Reset
Percentage). After you have the oil changed, you must execute
the following procedure. Press the OIL CHANGE RESET switch
and hold for five seconds as the M/C counts down for five
seconds. After a successful reset the Message Center will display
“OIL LIFE RESET TO 100%.” If you have established a
Personalized Oil Reset Percentage, the display will show that
percentage instead of 100%. To ensure accurate oil life
indicators, perform this reset procedure only after an oil change.
Your Personalized Oil Reset Percentage allows you to establish a
smaller oil change interval than the manufacturer’s
recommended interval. To establish your Personalized Oil Reset
Percentage perform the following procedure:
1. Press and hold the OIL CHANGE RESET switch and press
the RESET switch while the display is still counting down
the 5 seconds to reset. The display will change to “START
OIL LIFE AT XXX%.”
2. Press the OIL CHANGE RESET switch until the displayed
percentage is the Personalized Oil Reset Percentage that you
desire. Your choices are 100%, 90%, 80%, 70%, 60%, 50%,
40% and 30%.

Posted on Oct 15, 2008

  • 2 Answers

SOURCE: resetting oil change dash light

Turn ignition key to the on position (with engine off). Depress accelerator pedal 3 times. Oil change light should blink and you should here a beep, light will go out. Turn ignition key off.

Posted on Dec 10, 2008

  • 398 Answers

SOURCE: Staedy Service Engine Soon Light is on Dash board, How To Fix this Problem?

yes and no disconnect the battery both sides, now without touching the battery touch black to red wires, this resets any codes. if the light comes back on you will need a pcm scan to get any error codes from it.

Posted on Apr 23, 2009

  • 7353 Answers

SOURCE: how do you get rid of the change oil light in dash

turn the key on, the push and release the gas pedal 3 times, to the floor, this should reset the light. you may have to do it more than once for it to work.

Posted on Sep 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i reset oil change button?2003 model Toyota hillux extra cap


Turn the ignition key to 'ON' and press the odometer button until the display reads ODO (not Trip A or B).
Turn the ignition key to OFF.
Hold in the same button you used in step 1.
While holding the button in, turn the ignition key to ON.
The ODOMETER will change to:
5 dashes - - - - -
Then 4 dashes - - - -
Then 3 dashes - - -
Then 2 dashes - -
Then 1 dash -
THEN all zeros 0 0 0 0 0
Then back to the correct mileage.
Then the Maintenance Required light should blink and go out.

Aug 03, 2016 | Toyota Cars & Trucks

1 Answer

How do u clear the code of change oil light on a 1999 grand am


on the drivers side end of the dash there is a removable panel that sometimes says fuses on it. You will need to have the door open to remove it. Once it is off you will see a red reset button. Turn the key on. push the reset button one time, the change oil light should start to blink. if not press it again. Once the change oil light is blinking press and hold the reset button for about 10 seconds. an audible tone will beep three or four times and the light will go out.

Jun 23, 2011 | 1999 Pontiac Grand Am GT

1 Answer

I have changed the oil &filter,and the light on dash is still on telling me change oil,and motor requiers service soon. rev.counter does not work, can you help please. email s.stephen@clear.net.nz


Resetting Engine oil Life Monitor
1, turn key to on, but do not start.
2. Press ENG MET button on the Trip Monitor within five seconds.
3. Within five seconds of step 2, press and hold RANGE button on the Trip Monitor. The CHANGE OIL light will flash.
4.Hold the RANGE button until the CHANGE OIL light stops flashung and goes out. This should take about 10 seconds.

If it doesn't reset turn key off and repeat the procedure. Careful to observe the "within 5 seconds"

necss03

Nov 23, 2010 | 1991 Chevrolet Corvette

1 Answer

Need clear oil and tire codes lights on the dash are on


1st you need to look on the drivers side , end of dash between door there is a fuse box,, there should be a red reset button inside, with the key on every time you push it first the tire light will flash, the next time you push it the change oil light will flash, so you keep pushing it to what you want to reset and hold it in , you will hear several beeps,,, it will be reset

Aug 29, 2010 | 2000 Oldsmobile Alero

2 Answers

Change oil reset button location?


My change oil reset button on my 2002 Grand Am is in the fuse box by the drivers door. Turn the key on (so all dash lights are on), push the red reset button until the "change oil" flashes, then hold the button down until it clears from the dash. This should take care of it.

Nov 29, 2009 | 2002 Pontiac Grand Am

2 Answers

How do i clear the oil dash reminder light


Normally, changing the oil and filter will work. If your oil pressure is too low to turn the indicator off, you have other problems.

Nov 27, 2009 | 2005 Chevrolet Colorado

1 Answer

Changed the oil in 2004 chevy silverado 5,4 liter. the need to change oil light is still displayed on dash. How do I reset this


you got to hold the oil change menu button down for atleast 5 secs to clear the computer and go to 0 percent oil life used

Oct 05, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

Clear change oil message


turn the ign switch on too where your dash lights come on
then hit the gas peddle 3 times real quick!!
you may have too do this several times too get it cleared!!!

Apr 14, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

Change oil light stays on for a few seconds


you must reset the oil life . WITHOUT STARTING THE ENGINE, put ignition in the ON position with the dash lights on. NOW this MUST be done within 10 seconds. Push the gas pedal all the way down to the floor and release 3X. This should clear the light. Sometimes necessary to repeat if not done in a timely manner.

Mar 24, 2009 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
1998 Oldsmobile Intrigue Logo

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...