Question about 2001 Jeep Grand Cherokee

1 Answer

2001 grand cherokee idles funny

It idles high, then low. I have seven codes that come up. 4 of the code are oxygen sensor, I know but I have three I can't figure out why they are coming up. The 4 oxygen sensor codes are p0136, p0132, p0152, and p0138. The other codes are p0031 ho25 heater control, p0051 ho25 heater control, and p1499 hydraulic fan solenoid ckt. What could be the problem? please help!!!!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

Hi there, do you get water from the air conditioning unit entering the passenger foot well, if so then perhaps water is dripping onto the electrics below and causing these problems (blocked evaporator unit) alternatively, get jeep to reset your system (2 minute job) and this should work, keep an eye on it as the first new code that appears should be the problem area, hope this helps

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can i reset the 2007 Pontiac G5 ECU after changing the Oxygen sensor upstream.


What was the original code ? Did it have the work circuit anywhere in the code description ? Circuit low or circuit high ? An what are the seven codes you pulled now?

Oct 11, 2016 | 2007 Pontiac G5

1 Answer

2005 jeep grand cherokee Po204 205 175 174 138 158. Runs rough. Whats wrong?


PO204,205 are injector circuit malfunction,PO174 is a system lean code, PO175 is system rich code, PO138 is heated oxygen sensor bank1 sensor 2 circuit high voltage, PO158 is heated oxygen sensor bank2 sensor 2 circuit high voltage. This is a repair for your mechanic. When they fix the injector and o2 circuits the rich lean codes will also be repaired. Continued driving will ruin your catalytic converter. Good luck

Jun 13, 2015 | 2005 Jeep Grand Cherokee

1 Answer

What does code PO108 mean on a 2001 Grand Cherokee


wow , you actually tried to look it up, a 1st time here.

the MAP is a baro sensor used to calculate fuel injection RATES.

if you have gross air leaks to the system the engine IDLE screams.

is it?

108 means the voltage is too high.

usually its unplugged, or bad sensor.

otential causes of a P0108 code: Bad MAP sensor Leak in vacuum supply line to MAP sensor Engine vacuum leak Short on signal wire to PCM Short on reference voltage wire from PCM Open in ground circuit to MAP Worn engine causing low vacuum



Bad MAP sensor Leak in vacuum supply line to MAP sensor Engine vacuum leak Short on signal wire to PCM Short on reference voltage wire from PCM Open in ground circuit to MAP Worn engine causing low vacuum



http://www.obd-codes.com/p0108



and last. but before ECU.

low engine compression, is 1 more, causes , many



what i do is reseat the MAP sensor

i then make sure he vacuum port is not clogged. (both sides)

i then measure the output , keyon, and idle and gunning throttle.

any Voltmeter works here,

key on is 5v or near.

idle 1.8v

gun engine as the RPMs fall like a rock the volts tries to hit 0.5vdc.



http://www.fixkick.com/look/odds-ends/jeep/MAP-sensor-output-real.jpg



very very easy to find with a voltmeter

if the meter agrees with vacuum gage, then the MAP is ok

and you have air leaks or low vacuum for (VAST reasons)

ask.

Aug 19, 2014 | 2001 Jeep Grand Cherokee

1 Answer

Idles rough and low intermittently. Stalls occaisionally. Error code P1137 pulled off of the computer. 2001 Alero, 2.4L Automatic trans


P1137 is HO2S Bank 1 Sensor 2 Lean Or Low Voltage. Oxygen sensor is reading a "lean condition". This code probably is stored from the rough and low idling. So it sounds like you maybe having other issues causing this P1137 code to come up. For lean conditions read this:
1. Vacuum leaks - check for failed or loose vacuum lines, leaking intake gaskets, intake air tubes loose or any other source of un-metered air leaks (leaks after the Mass Air Flow Sensor)
2. Restricted fuel filter or bent/pinched fuel system lines
3. Incorrect input from other sensors, such as the Mass Air Flow Sensor/cam or crank sensors, which may not always drop a separate code
4. Engine misfire ? Yes I know this one may seem weird. You might think that if there is a misfire then you will have all that unburned fuel and it should read rich; right? Well the O2 sensors read only oxygen content in the exhaust, so if you have all that unburned fuel from incomplete combustion then, you guessed it, you also have all that unburned oxygen. High O2 content in exhaust equals a lean reading!

Sep 07, 2011 | Oldsmobile Alero Cars & Trucks

1 Answer

Where is the MAP sensor located on a 2001 Jeep Grand Cherokee?


ITS INTHE INTAKE MANIFOLD MAP STANDS FOR MANIFOLD ABSOLITE PRESSURE THE SERVICE CODE SHOULD BE PO1106 HIGH VOLTAGE OR PO1107 LOW VOLTAGE IF YOU DON;T HAVE THESE CODES THEN ITS PROBELY NOT THE MAP SENSOR REPLACING COMPOUNETS SHOULD BE THE LAST STEP FORM A PLAIN IM NOT SAYING MAP IS NOT THE PROBLEM BUT BLINDLY REPLACEING SENSORS CAN BE A COSELY MISTAKE GET CODES

Oct 19, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I have code p0137 coming up on my 2003 jeep grand cherokee laredo what does the code mean?


P0137 - Oxygen O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)

Essentially the same as P0136, P0137 refers to the second oxygen sensor on Bank 1. P0137 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This, is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 1 Sensor 2 is located to the rear of the catalytic converter and should produce an output signal relative to oxygen storage capacity of the catalytic converter. This rear (sensor 2) sensor is less active than the signal produced by the front sensor. However, if the ECM senses the sensor is inactive, this code will set.

Symptoms: There may be no visible symptoms to the driver, other than the MIL (Check Engine / Service Engine Soon) illumination.

Causes: A code P0137 may mean that one or more of the following has happened:
* Faulty o2 sensor Exhaust leak near the rear sensor
* Plugged catalyst
* Short to voltage on O2 signal circuit
* High resistance or open on O2 signal circuit

Possible Solutions:
* Replace faulty sensor
* Repair exhaust leak near the rear sensor
* Check for restriction in catalyst and replace as necessary
* Repair short, open, or high resistance on o2 signal circuit

Hpe hti shelps (remember comment and rated this).

Jul 26, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Error code P 0161 for 2000 Grand Cherokee Limited V8


Its related to the oxygen sensor and/or oxygen sensor heater. There are 4 sensors the Jeep is equipped with.

In most cases one of the recommended solution for all those faults is a sensor replacement, however before doing that and spending a lot of money. Go to auto zone and have them tell you what O2 sensor is bad buy it and replace it. Go back to them to have the code cleared. O2 sensors run 20-50bucks. Good Luck

Jun 20, 2009 | 2001 Jeep Grand Cherokee

1 Answer

99 Saturn SC1 ''Service engine soon'' light is on.


Did you get the code that triggered the SEL? If you know that, it will be easier to diagnose your problem. You can do it without a tool on the old saturns. Just need a paperclip. :

Use a paper clip to jumper Terminal A and B of the ALDL *Assembly Line Diagnostic Link* which is above your left knee.
Terminal A is an interal ground and is the top right terminal in the connector. Terminal B is directly adjacent and to the left of Terminal A.

Turn the ignition to ON.

All codes are 2 digits between 11 and 99. Codes are displayed on the SES light by flashing the light with short and long pauses to distinguish digits of one code from digits of another. The short pause is used between digits of the same code, long pauses are between codes. Also, each code is flashed three times before going to the next code.

For example, the sequence of code 12 will be: flash, pause, flash-flash, long pause, then repeat 2 times. If Code 12 is not displayed, the self-diagnostic pogram i snot functioning properly.

If only Code 12 is displayed, no system malfunctions have been stored.

Any existing system fault codes are displayed in order from low to high, except for Code 11.

On vehicles with an automatic transaxle and on which exist stored transaxle codes, Code 11 will be displayed last, then the SHIFT TO D2 light will begin flashing transaxle codes of flags.

When all engine codes have been displayed, Code 12 will flash again.

Diagnostic Codes
11. Transaxle Codes present
12. Diagnostic System Check
13. Oxygen sensor, circuit open or not ready
14. CTS circuit, out of range high
15. CTS circuit, out of range low
17. PCM fault, pullup resistor
19. 6x signal fault, no 6x signal between reference pulses
21. TPS circuit, out of range high
22. TPS circuit, out of range low
23. ATS circuit, out range low
24. VSS circuit, no signal
25. ATS circuit, out or range high
26. Quad Driver output fault
32. EGR system fault
33. MAP sensor circuit, out of range high
34. MAP sensor circuit, out of range low
35. IAC valve, rpm out of range
41A EST circuit open
41B EST circuit shorted
42A Bypass circuit grounded
42B Bypass circuit open
42C Bypass circuit shorted
41. EST bypass, open or shorted
42. EST bypass, open or shorted
43. ECS (knock sensor) circuit open or shorted
44. Oxygen sensor indicates system lean
45. Oxygen sensor indicates system rich
46. Power steering pressure switch circuit, open
49. Idle rpm out of limit high (vacuum leak)
51. PCM memory error
55. A/D converter error in PCM
81. ABS message fault (1993 vehicles with TCS)
82 PCM internal communication fault


Diagnostic Flags
27. Quick quad driver output fault (1993 only)
48. Reference imput intermittent or noisy
52. Battery voltage out of range
53. ESC knock present
54. Five volt reference ground
58. Battery voltage unstable
61. 6x signal fault
63. Option check sum error
67. Handwheel sensor circuit fault
71. Cooling system temperature high
72. Coolinng system temeprature low
73. CTS sensor unstable
74. CTS/transaxle temperatuer sensor ratio error
76. ATS sensor unstable
83. Low coolant (1993 only)

Feb 24, 2009 | 1993 Saturn SC1

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

Related Topics:

677 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...