Question about 1996 Chevrolet Blazer

1 Answer

Unable to pull out rear axle to change brearing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,927 Answers

Remove differential cover,turn axle until chunk turns around to access the small 5/16pin bolt remove pin bolt ,slide spider gear axle rod out ,go to axle ur working on and push axle inward ,ther is a c shaped key on end of axle where u took spider axle rod out remove this key easly by hand and pull axle out,,,note do not turn chunk after removing spider axle rod or ur spiders will fall out

Posted on Jun 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the rear wheel hub on a 98 Z71


To change the bearing , you have to pull the axle. Jack the rear end up and use support jacks. Remove the differential cover, oil will come out. Put the transmission in neutral. Spin the differential until you see the bolt that holds the center pin, remove both. remove the tires. push the axle in. remove the clip one the end of the axle in the differential. pull the axle out. You can chisel the bearing out. But they do have tools that get them out.
26208027-ntpj3zzbu2souu1dk5yahwp3-4-0.gif

May 29, 2016 | Cars & Trucks

1 Answer

How do you change rear axle seal on 1993 f 250


pull rear cover, pull center pin bolt out, pull pin, push axle in to drop clip, pull axle out, remove old seal, install new one and reverse above

Jun 03, 2011 | 1993 Ford F250

1 Answer

Fluid leak from left rear axle housing


This is caused by a leaking rear axle seal you will need to pull the left rear axle out and change the seal and check for a worn axle bearing, this requires the removal of the differential cover, pin and center block or posi spring and clutch pack (if so equipped) and spider gears and then the "C" clip that retains the axle into the gear carrier, u will need a tube of silicone to reseal the cover and a axle seal installer tool and about 2 hours of your time

Oct 28, 2010 | 2000 Ford Mustang

1 Answer

Procedure for changing bent r rear axle on 1997


if it has the four bolts that have a flange piece on it also then its just a unbolt and pull one.another sign of the unbolt/pull type is there is no removable cover on the back of the diff. i never undo nothing but the 4 bolts. i leave twn in but real loose so when i yank on the axle it wont break nothing when it cuts loose all of a sudden.

May 30, 2010 | 1997 Toyota T100

1 Answer

1998 F-150 rear driverside drum brake has oil in it. I think it is the axle oil seal on that side. How do I change it?


take off the wheel and check to see if the axle is bolted to the rear end or poss have to take off the diff cover to take the axle hold down clips off then pull out the axle pull out the seal reinstall new one

Mar 28, 2010 | 1998 Ford F150 Regular Cab

1 Answer

Change rear whell seal 1997 f-150 gear oil comeing out of rear whell took tire off; took drum off; and saw gear oil all over brake shoes. Seal or bearing need to be replace? how?


replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

Mar 24, 2010 | 1991 Ford F250

1 Answer

How do you change the bearings on the rear axle of a f150 Ford pickup? And does my year model require the bearings to be pressed on?


you have to block up the rear end then pull the cover off the rear end then pull tires and drums off then
go to the punkin and pull the center pin out its a 5/16 or 8mm bolt out slid the pin out then push axles in take the C-clips out then pull axles out
you will need a axle slide hammer to get the bearing out and
then tap the new one in just far enough to get the cyl. in
then put all back to gether

Mar 07, 2010 | 1996 Ford F150 Regular Cab

1 Answer

Rear axle


The Cheapest you can Get is @ A Pick A Part or Pull A Part, These are Auto Salvage yards that
You Go to With Your Tools And YOU REMOVE the Parts Yourself and they Charge VERY VERY REASONABLE Price for ALL PARTS. they Have Web sights that Tell All LOCATIONS.

Im Looking at Pull A Parts PRICE LIST and It Shows REAR AXEL'S DIFF COMPLETE for
DRUM BRAKE TYPE AXEL is $68.19 And DISC BRAKE TYPE Priced @ $73.87

http://www.indypickapart.com/contactus.html
Phone Number:
317.925.CARS (2277)
Unable to Find Other LOCATIONS uther than Indianapolis BUT, There May Many More
_________________________________________________________________________
NOW Pull A Part Does Have a Page for there Other Locations Try These Links
http://www.pullapart.com/

http://www.pullapart.com/Locations/Main.aspx

Jun 30, 2009 | 1997 Dodge Ram 1500 Club Cab

2 Answers

Rear bearing


rear axle bearings I assume? Pull the diff cover, rotate the carrier so you can remove the pin from the center of the 4 spyder gears, push the axle in slightly, and remove large c clip from the carrier area. The axle will pull right out! These vehicles are hard on axle bearings. Look them all over.

Good Luck!

Apr 02, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Need to know how to change rear wheel bearing in a 95 suburban


jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers

Jan 16, 2009 | 2003 GMC Sierra

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...