Peugeot 807 faults

The five beeps - five times would indicate a code 55 , but factory service info only goes to code 53 .

• Audible tone - DTCs retrieved

• Air bag SRS system fault

• REFER to DTC Priority Table.

Did your air bag light flash at all ? Apparently this will do flash the air bag light codes as well .
Symptom Chart Condition Possible Sources Action

• Air bag warning indicator is illuminated continuously

• Fuse
• Damaged wiring, terminals or connectors
• A faulty diagnostic connector
• A faulted RCM
• A faulty instrument cluster

• Go To Pinpoint Test A .

• Air bag indicator flashing

• Air bag/pretensioner supplemental restraint system (SRS) fault

• REFER to DTC Priority Table.

• Audible tone - DTCs retrieved

• Air bag SRS system fault

• REFER to DTC Priority Table.

• No communication with the restraints control module (RCM)

• Fuse
• Diagnostic tool
• Data link connector (DLC)
• A faulted RCM
• Circuitry

• Go To Pinpoint Test V .

LFC - light flash codes .
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Table
DTC a LFC b Description Action To Take - Continuous The Air Bag Indicator is Illuminated Continuously, RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground Go To Pinpoint Test A . B1231 13 Crash Data Memory Full Install a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . B1317 Continuous Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to Section 414-01 . B1318 Continuous Battery Voltage Low CHECK battery voltage; to be above 9.0 volts. REFER to Section 414-01 . B1342 12 RCM Is Faulted Install a new RCM. B1869 NONE
Continuous lamp
Secondary air bag warning sounds if another fault is present Lamp Air Bag Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test B . B1870 NONE
Secondary air bag warning sounds if another fault is present Air Bag Warning Indicator Circuit Short to Battery Go To Pinpoint Test C . B1891 53 Air Bag Tone Warning Indicator Circuit Short to Battery Go To Pinpoint Test D . B1892 53 Air Bag Tone Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test E . B1921 14 Air Bag Diagnostic Monitor Ground Circuit Open Go To Pinpoint Test F . B2292 33 Restraint System - Safety Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test G . B2292 34 Restraint System - Safety Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test G . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2294 24 Restraint System - Curtain Fault (Driver Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2294 25 Restraint System - Curtain Fault (Passenger Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2295 22 Restraint System - Side Air Bag Fault (Driver Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2295 23 Restraint System - Side Air Bag Fault (Passenger Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault (Front Impact Severity Sensor Circuit Fault) Go To Pinpoint Test K . B2296 43 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 45 Restraint System - Impact Sensor Fault (Driver Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 44 Restraint System - Impact Sensor Fault (Passenger Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 46 Restraint System - Impact Sensor Fault (Passenger Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2434 51 Driver Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test L . B2435 51 Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test M . B2438 52 Passenger Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test N . B2439 52 Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test O . B2477 Continuous Module Configuration Error INSTALL a new RCM. B2691 51 Driver Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test P . B2692 52 Passenger Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test Q . C1414 15 Incorrect Module Design Level Go To Pinpoint Test R . C1947 49 Driver Seat Track Position Sensor Circuit Short to Ground Go To Pinpoint Test S . C1948 49 Driver Seat Track Position Sensor Circuit Resistance Out Of Range Go To Pinpoint Test T . C1981 49 Driver Seat Track Position Sensor Circuit Fault Go To Pinpoint Test U . - - No Communication with the Restraints Control Module Go To Pinpoint Test V . Your best bet have codes checked with a scan tool .

B2293

Pinpoint Test H: LFC 19 and 21/DTC B2293 - Restraint System Airbag Status
Normal Operation
The restraints control module (RCM) checks all of the front air bag circuits for faults. If the RCM detects one of the following faults on any of the front air bag circuits, it will store diagnostic trouble code (DTC) B2293 in memory and, depending on the fault, flash either lamp fault code (LFC) 19 or 21 (or higher priority code if one exists) on the air bag indicator.
Fault Conditions
The RCM monitors for the following fault conditions:

• low resistance.
• circuit open.
• circuit short to voltage.
• circuit short to ground.

Possible Causes
A driver air bag status fault can be caused by:

• damaged wiring, terminals, or connectors.
• a faulty clockspring.
• a faulty driver air bag module.
• RCM is faulted.

A passenger air bag status fault can be caused by:

• damaged wiring, terminals, or connectors.
• a faulty passenger air bag module.
• RCM is faulted.

21 Restraint System - Air Bag Status (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H .

It's not unusual for 207s to show the anti-pollution warning randomly. In my experience it isn't significant and you just learn to live with it, but as yours is consistently showing at start up accompanied with the engine management light, it maybe something more serious. If the car appears to be driving okay, then I would be inclined to ignore it, if not, you will have to have a Puegeot dealer put it on their computer diagnostic machine - pricey !

207s have a bad reputation for random fault indications as a whole (Google it), some of which seem to be ambient temperature related - my father's 207 randomly shows the air bag light on very hot days but this goes away after a few start/stop cycles and a drop in temperatures. Fortunately, his MOT is due in March so when it goes for an MOT the light is always off - air bag fault indication showing is now an MOT failure.
Some people wouldn't be happy driving with an air bag indication, or any other fault indication, showing even for a short period of time, so this is a personal decision as to what you do about it.

Ford Airbag Fault Codes
Flash Code Component/Fault Description
- No Air Bag Indicator - Inoperative Indicator Circuit
- Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor
Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 Right Radiator Primary Crash Sensor Feed/Return Circuit Open
42 Left Radiator Primary Crash Sensor Feed/Return Circuit Open
44 Right Radiator Crash Sensor Not Mounted to Vehicle Properly
45 Left Radiator Crash Sensor Not Mounted to Vehicle Properly
51 Airbag diagnostic Monitor Internal thermal fuse Blown
52 Back-up Power supply Voltage Boost Fault
53 Front Crash Sensor High Resistance or Diagnostic Monitor Failure

it is possible the clock spring i agree,it is the common problem of the open circuit at the system

Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

this is a very common fault and you are right about it being a poor conection! the fault is on the horn contacts on the steering wheel. to do this you need to remove the air bag and this should only be done by a trained profesional as they contain an explosive charge!!
once this is off you just remove the 4 screws holding the horn switch, remove it and clean the contacts.

let me know if this helps
cheers

it could be cause of air bag fitment . just check with same technician for horn who done the air bag job.

In my opinion there might be a problem of wiring after changing the indicator console as there is connection problem of air bag in steering wheel. If there is a loose connection for any air bag the light goes on. You have to recheck the wiring and any loose connection for your air bag of steering wheel. But be sure to disconnect the battery terminals before you try to find out any fault in this area.

you have to be careful with the airbag connectors, they may look fitted but sometimes they dont go fully in - so check. on the steering wheel there is a black earth wire connected to a male connector, you need to cut the end off the wire and put a round earth terminal on it, then drill a small hole in the metal part of the steering wheel and fit a self tapping screw through the electrical connector you fitted and screw it into the hole you drilled. that is the usual cause for the horn not working e.g. bad earth connector on steering wheel. if you are not sure ask someone that knows about electrics