Question about 2002 GMC Yukon XL

Open Question

A/c belt on 02 yukon xl came off. is there a trick to replace

Posted by on

  • Colin Stickland
    Colin Stickland May 11, 2010

    no trick ,just dirty work

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: how do you replace a serpentine belt for a 2003 Yukon XL

Not Hard at all! You are going to have to Locate the Tensioner (Should be to the Inside of the A/C Compressor and Looks like a Large Wheel with a Arm in the Back going Down to a Smaller Wheel Underneath the Belt Pushing it up) There is a Nut in the Middle of the Large Wheel. Get a Wratchet and Socket and Turn this. It will Lower the Smaller Wheel and let the Tension Off of the Belt, While at that Point Remove the Belt from the Small wheel and Slowly Release the Tensioner. Reverse to Put Back.

Posted on Jan 03, 2009

smarthome2
  • 1114 Answers

SOURCE: 02 yukon denali xl wont start

Did you try to replace the starter cable? is the Truck turning over or just clicking.? If it's turning over and not starting. Best guess would be one of two things. Knock sensors Located under intake manifold. they get wet and deteriorate or the fuel pump. I've replaced all three on mine. 233k still running strong...

Posted on May 24, 2009

SOURCE: u-joint repalcement for 2001 yukon xl

Mark your drive shaft coincidenly with the rear axle and tranny. Remove drive shaft. Press out the old u joints and press in the new. You will need a torch for heat and a lot of patience. Have fun!

Posted on Jun 20, 2009

  • 8 Answers

SOURCE: i have a 02 gmc yukon xl what size is my door

6 3/4 but some 6.5 will fit

Posted on Nov 15, 2009

mx5turbo92
  • 545 Answers

SOURCE: belt squeal on 2007 Gmc Yukon denali xl with

yes sir your tensioner is self adjust but i think you need a new drive belt.i hope this will help,have a wonderfull holiday.

Posted on Dec 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many qt transmission fluid for 2002gmc yukon xl


5 quarts on an '02, also use the Dexron VI full synthetic

Nov 12, 2016 | 2002 GMC Yukon XL

1 Answer

2003 yukon ac compressor


need a tensioner tool, and pull back on tensioner to give room for new belt

Jul 01, 2012 | 2003 GMC Yukon XL

1 Answer

I Have 02 GMC DENALI XL AWD 6.0 vortex. I am noticing ticking noises from my engine during warm up, idle and while driving. The oil i always use is 10w30 castrol synthetic, change every 4k miles. Currently...


it is a lifter sticking till motor gets warm it happens in time i know a trick put i help so much for free.it will be fine try a highmile oil and check it every fill up my be low.

Jan 26, 2011 | 2002 GMC Yukon XL

1 Answer

'02 GMC Yukon - Backup Lights


have you tried replacing the switch on the gearbox????

Apr 02, 2010 | 2002 GMC Yukon XL

1 Answer

Belt squeal on 2007 Gmc Yukon denali xl with 46,000 miles. Isn't the belt tensioner self-adjusting? Does the belt need to be replaced?


yes sir your tensioner is self adjust but i think you need a new drive belt.i hope this will help,have a wonderfull holiday.

Dec 17, 2009 | 2007 GMC Yukon

1 Answer

Putting on a new serpentine belt on my gmc yukon and can't quite get it to go on, what is the trick? Tried even using a little dawn liquid on the edge of the alt. pulley and wouldn't go. Thanks Rick


nonononono.there is a tool for this you can pick up at sears. it gives you a little more leverage on the spring loaded tensioner that is used on this system.

Nov 04, 2009 | 2003 GMC Yukon XL

2 Answers

02 yukon my power window button does not work,


The door panel will have to be pryed off after all screws are removed and the motor must be replaced

Jul 29, 2009 | 2002 GMC Yukon XL

2 Answers

I have a 02 gmc yukon xl what size is my door speakers


Go to www.crutchfield.com and enter your vehicle info

May 05, 2009 | 2002 GMC Yukon XL

1 Answer

2001 gmc yukon xl 1500


Check to see if the power steering pump is still turning. If you have a broken drive belt (serpentine belt or "fan" belt), and the pump doesn't turn, you have no power assist. If the pump is still turning, check the fluid level in the reservoir.

Oct 31, 2008 | 2001 GMC Yukon

Not finding what you are looking for?
2002 GMC Yukon XL Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...