Question about 2001 Chevrolet Monte Carlo

2 Answers

2001 Monte Carlo Turn key on won't turn over, evertything else wo

Can jump across silenoid and car will turn over and start but immeditly shut off

Posted by on

  • sussexchief7 Jun 28, 2009

    If both keys will not unlock door I assume both batteries in openers are dead will this cause this issue>

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

Is there a security light on, if it is then you have the anti theft working thinking someone is trying to steal the car. If you have the second ignition key's with you try it.  If not try this, it takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps, keep me posted, be glad to help

Posted on Jun 28, 2009

  • Harvey N Tawatao
    Harvey N Tawatao Jun 28, 2009

    The fob key's don't immobilize the ignition. The ignition keys have a resistor on them that the ignition switch read's, that's why we are told not to put lot's of key's with the ignition keys. The extra key's wear down the contacts to the wires in the ignition switch for the immobilizer. let me know if the fob key's need to be re programed too, try replacing the battery's first and then we can re program them. Try this,  



    Transmitter Programming 
    No Tools Required 
    In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.
     
    Important 
    Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

    Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver. 

    Perform the following steps:
    Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat) 
    Remove the ignition key from the ignition lock cylinder. 
    Close all of the vehicle's doors. 
    Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis. 
    Turn the ignition lock cylinder to the ACC position. 
    Turn the ignition lock cylinder OFF, then back to ACC within 1 second. 
    Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

    Important 
    After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming. 

    Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. 
    Repeat step 8 in order to program each additional transmitter. 
    Remove the ignition key from the ignition lock cylinder. 
    Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis. 
    Validate that all the transmitters that were programmed operate properly.
    Good luck and hope this helps.  


  • kdub098 May 03, 2011

    i did this on my car and it worked thanks very much, but its temporary as soon as i shut it off it will do the same thing and wont turn over. is there anyway you can save this so i don't have to wait 30 minutes every time i want to start my car. thanks in advance.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 855 Answers

Car shuts off because switch is not in on position. Try rcking steering wheel back and forth while turning key. The switch could have to much pressure on it from the steering wheel lock. If rocking does not allow the key to turn the key and tumbler needs replaced.

Posted on Jun 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 Monte carlo z34 won't crank over unless I jump


Sounds like a problem with the key switch, probably the security system. You may only have power to the fuel pump when the engine is cranking.
Is the security light on or flashing ?

Jun 29, 2013 | Cars & Trucks

1 Answer

2001 monte carlo cooling fan running all the time and no temp indicated on the gauge


I had the same problem i had a manual shut off switch installed where i could turn the fan off and on from my dash by the steering column

Nov 17, 2012 | 2001 Chevrolet Monte Carlo

1 Answer

03 monte carlo ss won't start after driving a


If you are driving the car and it wont start after driving awhile. Do a wiggle on the CKP (crank position sensor) this sensor is located at the front main engine pulley, I am seeing a lot of loose male to female connection shut car off.

Feb 28, 2012 | 2003 Chevrolet Monte Carlo

1 Answer

I have a 2001 monte carlo and it won't start how can i bypass that i try the 10 minute wait and still won't start its been two day


Go to this link and look under "permanent fix". This is the only bypass for your system. Its either this or get it fixed.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Aug 02, 2011 | 2001 Chevrolet Monte Carlo

1 Answer

My 03 monte carlo will not cranck with the swith if i jump start silinoid it will start and shut back off in 2-3 seconds every time i jump start it.


sound like you have a problem with the anti-theft system
if you have the remote, check to see if the battery is good
try to crank your car ( it will not run ) let go the key so all the lights will be on ( make sure your battery is fully charged ).
leave it on for 10 minutes then turn it off.
wait for atleast two second then start it.
if all this do not work, you need to get your car to the dealer.
small shop may not be able to figure it out.

Mar 04, 2010 | 2003 Chevrolet Monte Carlo

1 Answer

I have a 97 monte carlo that wont start and the security lights blinks and wont go off. i have 2 pairs of ignition keys and both wont work. couldn't be the starter because i tried to jump start it by...


Try and reset it by getting in car make sure every thing is off, close door's turn key to on and way about 10 mins or till light stop's flashing, then turn key to off and start engine.

Feb 12, 2010 | 1997 Chevrolet Monte Carlo

1 Answer

My 2001 monte carlo having engine problem rpm jumping while driving and will also shut off


i had cars do this before usually its a part called idle air control valve or iacv if your car has one it affects your emmissions also try checking that part.yup stalls car out and everything check engine light comes on sometimes

Jan 24, 2010 | 2001 Chevrolet Monte Carlo

2 Answers

Car wont start. security light on.


I had this same problem with my 2002 Monte. It is a very cheap fix about $100(If you do not got to the dealer $800) The car thinks that you are trying to steal it so you have to turn the key in the on position until the security light goes off and when the light goes off dont try to start it. Turn the key to the off position and then try to start it. It should take about ten minutes. I know its frustrating cuz I've been there.

Aug 02, 2008 | 2007 Chevrolet Monte Carlo

Not finding what you are looking for?
2001 Chevrolet Monte Carlo Logo

1,848 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...