Question about 2000 Dodge Caravan

1 Answer

Electrical connector disconnection on cooling fans

I got everything off to remove the cooling fans, but I cannot determine how to disconnect the electrical connector. Is there a diagram somewhere that shows how to pull the red clip out?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 49 Answers

The red clip should just slide up not come off completely.

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove and replace the water pump on a 2006 Chrysler 300 hemi 5.7 l.


5.7L Engines

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Drain the cooling system.
  4. Disconnect negative battery cable.
  5. Remove the upper radiator hose.
  6. Disconnect cooling fan electrical connector.
  7. Remove cooling fan mounting bolts.
  8. Remove the radiator cooling fan assembly from vehicle.
  9. Remove the radiator fan assembly.
  10. Remove accessory drive belt.
  11. Remove thermostat.
    NOTE The water pump mounting bolts are different lengths. Note the location of the water pump mounting bolts.
0996b43f80200d65-mw3da2o1okphbx00ygfzxzdl-4-0.jpg To install:
  1. Install water pump and mounting bolts. Tighten mounting bolts to 20 ft. lbs. (28 Nm).
  2. Make sure double ended bolt is in the proper location. Tighten double ended bolt to 20 ft. lbs. (28 Nm).
  3. Position the radiator cooling fan assembly in vehicle.
  4. Install cooling fan mounting bolts. Tighten to 50 inch lbs. (6 Nm)
  5. Connect the cooling fan electrical connector.
  6. Install the upper radiator hose.
  7. Install thermostat.
  8. Install the accessory drive belt.
  9. Install the radiator fan assembly.
  10. Connect negative battery cable.
  11. Fill the cooling system.
  12. Pressure test cooling system.

Mar 16, 2017 | 2006 Chrysler 300

1 Answer

How to change a coolant fan for a 2001 impala


  1. Disconnect the negative battery cable.
  2. Partially drain the cooling fan.
  3. Raise and support the vehicle. Refer to Vehicle Lifting.
  4. Remove the transmission oil cooler lines from the retainers at the bottom of the cooling fan shroud.
  5. Remove the lower fan shroud push pin retainers.
  6. Lower the vehicle.
  7. Remove the right and the left engine mount struts.
  8. Remove the left front fender upper diagonal brace.
  9. Remove the radiator inlet hose from the radiator.
  10. Remove the air cleaner assembly.
  11. If equipped remove the cooling fan heat shields.
  12. Disconnect the cooling fan shroud electrical connectors.
  13. Remove the cooling fan shroud bolts.
  14. Disengage the cooling fan shroud clip from the top of the radiator.
  15. Remove the cooling fan shroud.


25010346-uuob5xk5qpmufdktz2iyu4qm-2-0.gif

Aug 25, 2014 | 2001 Chevrolet Impala

1 Answer

Coolant system


you have to drain cooling system and disconnect cooling fan electrical connector and remove the cooling fan shroud assembly with radiator.you need quick disconnect coupling tool to detach the transmission cooler lines from the radiator.you can buy quick disconnect tool at any auto parts stores.

May 18, 2013 | 2004 Ford Freestar

1 Answer

How do i get to the ac fan motor 2000 jimmy


  1. Disconnect the VCM or the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.

  1. Disconnect the electrical connector
  2. Remove the 5 blower motor and tan assembly mounting bolts
  3. Remove the blower motor and fan assembly
    Reverse procedure to install. Don't forget that cooling tube. It looks useless but is very important to reinstall.

Aug 15, 2012 | 2000 GMC Jimmy

1 Answer

AC or heater fan does not work?


The most common problem with these fans are the fan itself wears out, or the relay becomes burnt at the contacts inside, or both.

Blower Motor REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. If necessary on 1992 and 1993 Typhoons, remove the charge air cooler. For details, please refer to Section 3 of this manual. Fig. 1: Example of a common blower motor installation - vehicles without A/C shown 85386001.gif

  3. Disconnect the blower motor cooling tube.
  4. Disengage the electrical connector(s) from the blower motor, as necessary. NOTE: On some earlier models equipped with A/C, it may be necessary to disconnect the A/C vacuum tank and move it aside.
  5. Remove the blower motor-to-case screws, then carefully withdraw the blower motor from the case. To install:
  6. Install the blower motor to the case and secure using the retaining screws.
  7. Engage the electrical connector(s) to the motor, as necessary.
  8. If moved on early model vehicles, reposition and secure the A/C vacuum tank.
  9. Connect the blower motor cooling tube.
  10. If removed on 1992 and 1993 Typhoons, install the charge air cooler.
  11. Connect the negative battery cable. Fig. 2: Disconnect the blower motor cooling tube 86616001.jpg
    Fig. 3: Disengage the necessary electrical connector(s) from the blower motor 86616002.jpg
    Fig. 4: Loosen and remove the blower motor retaining screws 86616003.jpg
    Fig. 5: Withdraw the blower motor from the case 86616004.jpg
prev.gif next.gif

Nov 19, 2010 | 1991 Oldsmobile Bravada

1 Answer

2005 Jeep Liberty overheats at idle but while in movement temp returns to normal.


Check to see if the fan on the radiator is working at idle.

Here's information on how to change the fan if needed:

Engine Cooling Fan Removal & Installation 2.4L Engine To Remove:
  1. Remove the coolant bottle and set aside.
  2. Remove the power steering reservoir and set aside.
  3. Disconnect the cooling fan connector.
  4. Remove the cooling fan mounting screws and the cooling fan.
To Install:
  1. Install the cooling fan and the mounting screws. Tighten to 50 in-lb (5.5 Nm).
  2. Connect the cooling fan connector.
  3. Install the power steering reservoir.
  4. Install the coolant bottle.
3.7L Engine To Remove:
NOTE: If the fan blade is bent, warped, cracked or damaged in any way, it must be replaced ONLY with a replacement fan blade. DO NOT attempt to repair a damaged fan blade.
NOTE: For 3.7L Heavy Duty/Max Cool/Trailer Tow cooling package, the viscous fan cannot be removed separate from the shroud. Both fan and shroud must be removed together.
  1. Disconnect battery negative cable.
  2. Using special tool #6958 spanner wrench and #8346 adapters, remove the viscous fan from the water pump.
  3. Gently lay fan into shroud.
  4. Disconnect the electrical connector for the electric fan, then disconnect connector from shroud.
  5. Remove the two fan shroud mounting bolts connecting the fan shroud to the radiator.
  6. Remove the shroud and fan from the vehicle.
To Install:
  1. Install fan shroud assembly into the vehicle. Tighten fan shroud to radiator bolts to 50 in-lb (5.5 Nm).
  2. Install shroud mounting bolts tighten bolts to 89 in-lb (10 Nm).
  3. Connect fan motor wire connector to harness connector, and attach connector to shroud.
  4. Connect negative battery cable.
  5. Start engine and check fan operation.

Aug 31, 2010 | 2005 Jeep Liberty

1 Answer

Need instructions on how to replace the cooling


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Radiator upper crossmember
    • Fan motor electrical connector
  3. Drain cooling system below the level of the upper radiator hose.
  4. Remove or disconnect the following:
    • Upper radiator hose from radiator
    • Radiator fan fasteners and upper clip
    • Fan assembly by lifting upward to clear radiator
To Install:
  1. Install or connect the following:
    • Radiator fan assembly
    • Upper clip and fasteners
    • Upper radiator hose to radiator
    • Fan motor electrical connector
    • Radiator upper crossmember
  2. Fill cooling system.
prev.gif next.gif

Jul 17, 2010 | 2004 Dodge Intrepid

1 Answer

How to change the radiator fan?


Electric Engine Fan - Fan Switch

Removal & Installation
2.7L Engine
  1. Disconnect negative battery cable.
  2. Partially drain cooling system.
  3. Disconnect the electrical connector .
  4. Remove engine coolant sensor from coolant outlet tube .
To install:
  1. Apply thread sealant to sensor threads.
  2. Install engine coolant temperature sensor into coolant outlet tube.
  3. Tighten sensor to 20 ft. lbs.(28 Nm) torque.
  4. Connect electrical connector to engine coolant temperature sensor .

3.2L And 3.5L Engines
  1. Disconnect negative battery cable.
  2. Partially drain cooling system.
  3. With the engine cold, disconnect coolant sensor electrical connector.
  4. Remove sensor.
To install:
  1. Install engine coolant temperature sensor.
  2. Tighten sensor to 20 ft. lbs.(28 Nm) torque.
  3. Attach electrical connector to sensor.
  4. Connect negative battery cable.
Removal & Installation
  1. Disconnect negative battery cable.
  2. Partially drain cooling system.
  3. Remove upper radiator hose.
  4. Disconnect cooling fan electrical connector.
  5. Remove cooling fan mounting bolts.
  6. Remove radiator cooling fan assembly from vehicle.

    f9d971c.jpg
    Fig. Removal and installation of the radiator fan-2.7L Engine shown
To install:
  1. Position radiator cooling fan assembly in vehicle.
  2. Install cooling fan mounting bolts. Tighten to 50 inch lbs. (6 Nm)
  3. Connect cooling fan electrical connector.
  4. Install upper radiator hose .
  5. Fill cooling system.
  6. Operate engine until it reaches normal operating temperature.
  7. Check cooling system and automatic transmission for correct fluid levels.

Hope helps (remember comment and rated this).

Jul 13, 2010 | 2001 Dodge Intrepid

1 Answer

I need to reconnect my radiator in my 2000 ls v8


For 2000 Lincoln LS 3.9L SFI DOHC 8cyl...
Radiator - Removal & Installation
  1. Drain the engine cooling system.
  2. Remove the upper radiator sight shield.
  3. Remove the air cleaner outlet tube.
  4. Remove the six bolts and the two radiator upper support brackets.
  5. Remove the upper radiator hose.
  6. Remove the bolt and position the receiver drier aside.
  7. Disconnect the dual flow coolant valve electrical connector and the A/C line from the fan shroud.
  8. 3.0L engines only:
    Disconnect the Throttle Position (TP) sensor and the Idle Air Control (IAC) valve electrical connectors.
  9. Remove the bolts.
  10. Remove the bracket.
  11. 3.9L engines only:
    Remove the bolt and position the electric water pump aside.
  12. Disconnect the high pressure cooling fan bracket and line.
  13. Inspect the seal and install a new seal if necessary.
  14. Disconnect the return hose from the cooling fan and shroud.
  15. Separate the return hose from the fan shroud and position aside.
  16. Remove the two bolts and the fan shroud assembly.
  17. Remove the A/C condenser.
  18. Remove the two bolts and position the multi-cooler assembly aside.
  19. Remove the bolts and the condenser support brackets.
  20. Remove the radiator.

To install:
  1. Install the following:

    Radiator Condenser support brackets Multi-cooler assembly A/C condenser Fan shroud assembly
  2. Connect the return hose to the fan shroud
  3. Connect the high pressure cooling fan bracket and line.
  4. 3.9L engines only:
    Replace the bolt and position the electric water pump aside.
  5. 3.0L engines only:
    Connect the Throttle Position (TP) sensor and the Idle Air Control (IAC) valve electrical connectors.
  6. Replace the following
    The upper radiator sight shield. The air cleaner outlet tube. The six bolts and the two radiator upper support brackets. The upper radiator hose. The bolt and position the receiver drier aside.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2000 Lincoln LS

1 Answer

Replace the radiator


Removal and Installation
On all engines
  1. Drain the engine cooling system. For additional information, refer to Cooling System Draining, Filling And Bleeding in this section.
  1. Remove the upper radiator sight shield.
  1. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 .
  1. Remove the six bolts and the two radiator upper support brackets.
  1. NOTE: 3.9L shown; 3.0L similar.
    Remove the upper radiator hose.
  1. Remove the bolt and position the receiver drier aside.
  1. Disconnect the dual flow coolant valve electrical connector and the A/C line from the fan shroud.
On 3.0L engines
  1. Disconnect the throttle position (TP) sensor and the idle air control (IAC) valve electrical connectors.
  1. Remove the bracket.
    1. Remove the bolts.
    1. Remove the bracket.
    1. Disconnect the high pressure cooling fan bracket and line.
    1. Using the appropriate special tool, install a new O-ring on the power steering pressure hose fitting.
    1. Separate the return hose from the fan shroud and position aside.
    1. Remove the two bolts and position the fan shroud assembly.
    1. Disconnect the return hose from the cooling fan and shroud and remove the cooling fan and shroud assembly.
    1. Remove the A/C condenser. For additional information, refer to Section 412-03 .
    1. Disconnect the lower radiator hose.
    1. Remove the two bolts and position the multi-cooler assembly aside.
    1. Remove the bolts and the condenser support brackets.
    1. Remove the radiator.

Apr 29, 2009 | 2002 Lincoln LS

Not finding what you are looking for?
2000 Dodge Caravan Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...