Question about 2003 Chevrolet Silverado 1500

1 Answer

03 chevy silverado 1500 2wd

Its keeps going in to reduced engine power and i have an evap purge vent bad would that cause it? then more fuel i have in the truck the less likely it is to do it.. if its 3/4 or higher it doesnt do it

Posted by on

  • ousoon20890 Jun 27, 2009

    its a new fuel pump tho and why would it overheat? someone said ecm how do u feel about that? how would it over imeditally when i start it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 109 Answers

My guess is that the fuel pump is overheating when below 3/4 because it it is not covered in cold fuel

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007. What are the probable causes of DTC P0446?


DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.


?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.


?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .


?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system


Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

    Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
    If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

  1. Install the fuel cap.
  2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.
?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.



If

Sep 06, 2015 | Chevrolet Impala Cars & Trucks

2 Answers

045500 error code on a Chev silverado 1500 2009 5.3 lt what does it say


DTC P0455
  • Evaporative Emission (EVAP) System Large Leak Detected

Jul 23, 2014 | 2009 Chevrolet Silverado 1500

2 Answers

2002 Chevy Silverado po300 po449 codes


Have you checked the EGR valve? The P0449 EVAP code is normally or the purge solenoid on the intake. Unplug the line that feeds the EVAP system from the purge valve and connect a vacuum gage. It should flutter while it is activated. If not, that could be the culprit.

Dec 12, 2012 | 2002 Chevrolet Silverado 1500

1 Answer

I have code p0449 what is the problum


p0449 is EVAP (Evaporative Emission System) purge/vent solenoid circuit condition

possible causes are-- purge or vent valves are defective, check connector and wiring, fuel saturated vapor canister, Failed EVAP vent solenoid. plus check all hoses good. check for a bad fuel cap seal. remove cap and replace it, erase code and see if it comes back. go to this site maybe it will help you. www.gm-trucks.com/forums/index.php?showtopic=40659

Jan 21, 2012 | 2003 Chevrolet Silverado 1500

2 Answers

My 1995 subaru legacy lsi cuts out when I rev the engine around 1 rpm. Plus the check engine light is on. I took it to the dealership and they couldn't fix it, but they got a code from the check engine...


code p 0441 refers to evaporative emission (EVAP) system --incorrect flow detected ==== causes --- hose connection/s--- intake leak---EVAP canister purge valve replace the purge valve

May 21, 2017 | 1995 Subaru Legacy

1 Answer

I recently purchased this 1999 Chevy Blazer and it wont pass inspection because the OBD2 Diagnostic trouble code states it's problem is, code P0440-Evaporative Emission System. The guy said it looks like...


The evaporative leak detection diagnostic strategy is based on applying a vacuum to the EVAP system and monitoring the vacuum decay rate. The VCM monitors the vacuum level via the fuel tank pressure sensor input. At an appropriate time, the EVAP purge solenoid and the EVAP vent solenoid turn ON, allowing the engine vacuum to draw a small vacuum on the entire evaporative emission system. If a sufficient vacuum level cannot be achieved, a large leak or an EVAP system malfunction is indicated.

The following conditions can cause this problem:
* A disconnected or malfunctioning fuel tank pressure sensor
* A missing, malfunctioning, improperly installed, or loose fuel cap
* A disconnected, damaged, pinched, or blocked EVAP purge line
* A disconnected or damaged EVAP vent hose
* A disconnected, damaged, pinched, or blocked fuel tank vapor line
* A disconnected or malfunctioning EVAP purge solenoid
* A disconnected or malfunctioning EVAP vent solenoid
* An open ignition feed circuit to the EVAP vent or purge solenoid
* A damaged EVAP canister
* A leaking fuel sender assembly O-ring
* A leaking fuel tank or fuel filler neck

Any of the above conditions can set a DTC P0440.

Mar 08, 2011 | 1999 Chevrolet Blazer

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

1 Answer

The "engine power is reduced" light comes on


po455 is Probable Cause[s]

1. Defective, loose or missing fuel cap
2. EVAP canister broke, hose cracked or not connected
3. Purge or vent solenoid defective
4 . Vacuum leak at engine po121 code po121 means Throttle Position Sensor/Switch A Circuit Range/Performance Problem . it is usually indicative of a faulty throttle position sensor or faulty wiring harness in the engine bay.

Feb 27, 2010 | 2006 Chevrolet Impala

3 Answers

2000 cavalier check engine light code po440


P0440 - Evaporative Emission (EVAP) System


evaporative emission (EVAP) system has a large leak.
Check the gas cap or vent valve. these are the most common problems.


The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the Fuel tank pressure sensor (FTP). When the sensor indicates a small leak in the EVAP system, this code is set.


Here are some additional causes.

* A small leak in any of the EVAP hoses or fuel tank hoses
* A small leak in the purge valve or vent valve
* The EVAP Canister may be leaking

Jun 06, 2009 | 2003 Chevrolet Cavalier

2 Answers

HAVE A TROUBLESHOOTING MESSAGE PO446 ON A 2003 CHEVROLET SILVERADO 1500. CHECKED GAS CAP AND TIGHTNED NO CHANGE. AM LOOKING FOR LOCATION OF FOLLOWING PARTS PURGE OR VENT SOLENOID VAPOR CANISTER EVAP VENT...


DTC P0446 Evaporative Emission (EVAP) Vent System Performance

The vehicle control module (VCM) monitors the performance of the evaporative emission (EVAP) system by applying a predetermined level of vacuum to the EVAP system and monitors the vacuum decay rate. The VCM sets this diagnostic trouble code (DTC) if the vacuum decay rate is more than a predetermined value. The VCM monitors the amount of vacuum and the amount of pressure in the EVAP system by monitoring the fuel tank pressure sensor. For this DTC, the VCM turns ON both the EVAP purge valve and the EVAP vent valve when the Conditions for Running the DTC are met. This applies an engine vacuum to a closed EVAP system. The VCM turns OFF both the EVAP purge valve and the EVAP vent valve when the system reaches a correct amount of vacuum. The EVAP system should quickly RELEASE the vacuum in the EVAP system with the EVAP purge valve OFF and the EVAP vent valve OFF (open). This test indicates a blocked or restricted EVAP vent path if the EVAP system fails to release the vacuum quickly enough.

3208f98.gif


Dec 02, 2008 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...