Question about 1999 Jeep Wrangler

1 Answer

Rough running 99 jeep wrangler 4.0L 6 cylinder auto it started running rough and then would die and not restart we have replaced the cam and crank shaft sensors and ran fine then went to store came out and started it and it ran rough again but it is throwing the code for the sensors we just replaced

Posted by on

  • ksears Jun 27, 2009

    it will run fine for awhile then will start to raddle and ping and thows the same code then when we clear the code it will run fine

  • ksears Jun 28, 2009

    so we did a tune up on this last night cause it need one ran fine for awhile then it started running crappy again we let it sit and idle for awhile and it cleared itself up and was fine and it didn't through a code this time.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Jeep Master
  • 1,564 Answers

Computers aren't ALWAYS correct. If a code wasn't cleared after the original problem, it will read the same codes off to the diagnostic. I would remove the wire connector to each injector while it's running. If one of them makes no difference THAT is your culprit. Let me know please!

Posted on Jun 27, 2009

  • Dana Newcombe
    Dana Newcombe Jun 27, 2009

    You very well may be shopping for a new engine control module, don't be afraid to go to the salvage yard. Huge savings and these rarely go bad, but I've changed a few. Keep me updated, thanks.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A rough running Jeep wrangler


cranks ok> / not stated, and is 100% #1 key fact.
ill guess (daft) it cranks OK.
so check fluid levels(oil tops list )
then fuses.we test them.
then scan it.
all modern cars same. deal.

if it dont crank, "my starter is silent or just clicks)
then that be a horse of a different color.
dead battery ? charge system failure,
starter bad?
PRNDL (p/n switches bad )try cranking in neutral yet
my wrangler is 6 speed stick with a clutch switch
that too, is different.
even green battery lugs,.got those?

will not crank
or cranks perfect but will not start
which is it??????????????????????????/

Jan 14, 2016 | 2003 Jeep Wrangler

1 Answer

2000 Jeep Wrangler idels rough cold runs good warm.


Sounds like the Mass Airflow sensor (or MAF).

Oct 15, 2012 | 2000 Jeep Wrangler

1 Answer

What does the auto shut off fuse do? 92 Jeep Wrangler is having start up problems.


The auto shutdown relay in your vehicle is controlled by the computer. If the computer does not see a signal from the crank or cam sensor, it will turn off power to the relay which in turn shuts off power to the fuel and ignition system. Unlike those in many passenger vehicles, it's not connected to an impact sensor. (as jeeps are off road vehicles as well as being transportation, if they had an impact sensor, they would be prone to shutdown when traveling over rough off road terrain)
The fuses to the relay are affected by shorting or overload of any components they serve, or by a problem with the relay itself.

Nov 01, 2009 | 1992 Jeep Wrangler

1 Answer

99 jeep wrangler 4.0 won't start


yes the crank sensor is probebly your problem.

Jul 18, 2009 | 1999 Jeep Wrangler

1 Answer

Startin and runnin problems


Most common failure is crank sensor. Before running out and buying one, I strongly recommend that you do some further testing. Any decent manual has instructions for testing systems. Also: test both running and after it dies. (while running everything may check out as good) If you have spark when not running, check fuel filter as well!

Feb 03, 2009 | 2001 Jeep Wrangler

1 Answer

99 jeep wrangler


get a 6 cylinder motor drop in this is best gas saver for most vehicles 4 cylinders dont have the ability to push all the weight of a vehicle but runs smoothly
6 cylinders are as i put in words are evenly balanced for everyday use and not gas guzzler either

May 16, 2008 | 1999 Jeep Wrangler

Not finding what you are looking for?
1999 Jeep Wrangler Logo

Related Topics:

437 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...