Question about GMC Yukon Denali

1 Answer

Guages stopped working. don't know which fuse to change.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 48 Answers

I hate to say this but first i would check all the fuses to see if any of them is bad, if not then it is the wireing in the dash..........if it is not a fuse, then have it checked at the GMC garage or your mechanic.............

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas don't work change the sender still don't work


IF the guage is not working and you changed the sender, it is the guage. You cannot get just a guage, you have to replace the whole instrument panel or send the one that you have out for repair.

Jul 23, 2013 | Cars & Trucks

1 Answer

1991 safari digital guages don't work


Could be a problem with the connector at the back of the cluster, or the printed circuit board.

Jul 04, 2012 | 1991 GMC Safari

1 Answer

My gas needle stopped working. how will i know if gas tank is empty. If van sits in park and running the needle drop to E and the low fuel light comes on, then when you drive it goes back to a full tank....


You can take out the part of the dash where the guages are and change the little sensor/fuse behind the fuel guage, they should have a replacement part at orileys or autozone

Jan 09, 2011 | 2001 Pontiac Montana

1 Answer

Check guages light came on , 9 volts on guage,\radio died. charged batt. ran yesterday, today it wont start. battery has 12 v. turns over but no start.no guages work,when key is on. checked fuses,ok. no...


The main problem is the alternator has went out,and the battery voltage dropped to low for it to run.Most likely the computer has lost memory sense the battery was dead,or close to it.I don`t know the year,but this is most likely what happened.The computer would have to be reflashed at the dealership.But be sure to look for a main fuse to be blown,check all fuses,this might have happened,and not the computer.

Nov 03, 2009 | Dodge Pickup Cars & Trucks

2 Answers

Instrument guages stopped working


Hi, this could be as simple as a blown fuse. It could also be because of failed general parts. i would first check the fuse box to make sure all the fuses are good then, i would check the wire connections on the back of each gauge to see if they may have become lose or separated form the housing.

Feb 25, 2009 | 1997 Honda Accord

1 Answer

Chevrolet Blazer 1997.


If sender is new in the fuel tank, you have a wire problem between conection of fuel sender and dashboard gauge most likely place at dasbboard gauge.

Nov 27, 2008 | 1997 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...