Question about Nissan Quest

3 Answers

After the door closes, by hand or the motor, a few seconds later the rear end of the door pops loose. It pops open about a quarter inch or so. The car reports that the door is open. The front edge of the door still appears closed. This just happened last night for the first time. First the door wouldn't close at all, as the FRONT latch on the door was closed. I popped that open by hand (it looked like it was already closed). After that, apparently the front is closing, now not the back back.

Posted by on

  • klbrisby Jun 27, 2009

    The issue is with the right rear sliding door. Nothing in the first response, or in my own experimentation, seems to suggest the issue is lock-related. Though, hey, maybe. I need another opinion.

  • klbrisby Jun 27, 2009

    Looks like it was just a sticky (lube gunk) catch on that particular door. Neither solution appear to apply. By the way, what is "RM100+"? Writing from California, I don't recognize the denomination or currency. Malaysian??

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Nissan Master
  • 3,854 Answers

Look along the door frame, take a close look at the weather strip along the bottom of the runners and see if it was kicked down keeping the sliding door arm from sliding freely. If it has been kicked down preventing the bottom door arm from sliding, it will bind up keeping the door from sliding all the way to the close position. Good luck and keep me posted. If it is the bottom weather strip, you can buy some silicon gasket sealer and use it to glue the weather strip to the bottom of the body molding. If this works, you just saved your self $85.00 at the dealer for the repair. Use it wisely and go out to dinner.

Posted on Jun 28, 2009

  • Harvey N Tawatao
    Harvey N Tawatao Jun 28, 2009

    Almost forgot, check the door latch at the back to see if the latch is in the close position. If it is, just pull on the door handle like your opening the sliding door and put a pen at the latch to move it to the open position. Hope you understand what i am trying to say, kinda hard for me to explain. Let me try this. The door latch catches the door frame striker pin and the C lock closes, If the C lock is already close then the door striker pin is on the out side of the C lock and not holding. If that is the case, just hold the door handle open like your going to open the door and use a pen or a screw driver to pull the C clip on the door latch open. There I think i made better sense. Keep me posted. be glad to help.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,917 Answers

Hey,

No choice need to go to some accesories shop to do. Prepare around RM100+. Maybe cheaper. Thanks

Posted on Jun 27, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 296 Answers

Hi,

Central locking got problem. I'll just lock my passenger side door all the time. I asked before, its around RM100+ to get it done. Need to open everything, the door panel area. The "gun" which push the car locking mechanism at the driver side door spoild. This gun has 4 or 5 wire if not mistaken. The ground wire's connection may not be good. The shop worker would add a thicker wire n screwed the wire tightly to the metal part of the door panel. Straight away problem solved. The culprit was the grounding.

So if your problem still persists, try asking the shop to check your grounding as well. Might be the one causing the problem. Hopefully it turns out well for you. Thanks for contacting Fixya.

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the motor located for my rear quarter panel windows on my 05 Pontiac Montana SV6? And how do I test it?


Rear Quarter Window Actuator - Right (A20)
Behind the right rear interior body panel
Rear Quarter Window Actuator - Left (A20)
Behind the left rear interior body panel
Rear Quarter Window Inoperative

1

Did you review the rear quarter window description and operation?
Go to Step 2
Go to Symptoms - Body Rear End

2

Verify that the rear quarter windows are inoperative.
Do the rear quarter windows operate normally?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

Are both rear quarter windows inoperative?
Go to Step 4 yes
Go to Step 6 no

4

  1. Turn OFF the ignition.
  2. Disconnect the rear quarter window switch.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the accessory voltage circuit of the rear quarter window switch harness connector with a test lamp that is connected to a good ground.
Does the test lamp illuminate?
yes Go to Step 5
no Go to Step 7

5

Connect a test lamp between the accessory voltage circuit of the rear quarter window switch harness connector and the ground circuit of the rear quarter window switch harness connector.
Does the test lamp illuminate?
Go to Step 8
Go to Step 10

6

  1. Turn OFF the ignition.
  2. Disconnect the appropriate rear quarter window actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
  5. Activate the rear quarter window switch to the Open and Close positions.
Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

6

  1. Turn OFF the ignition.
  2. Disconnect the appropriate rear quarter window actuator.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the power window motor rear vents open control circuit of the rear quarter window actuator harness connector and the power window motor rear vents close control circuit of the rear quarter window actuator harness connector.
  5. Activate the rear quarter window switch to the Open and Close positions.
Does the test lamp illuminate?
yes Go to Step 9
no Go to Step 11

7

Test the accessory voltage circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
Go to Retained Accessory Power (RAP) Inoperative in Computer/Integrating Systems

8

Inspect for poor connections at the harness connector of the rear quarter window switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 12

9

Inspect for poor connections at the harness connector of the appropriate rear quarter window actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
yes Go to Step 14
no Go to Step 13

10

Repair the open in the ground circuit of the rear quarter window switch. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

11

Repair the open in the appropriate power window motor rear vents control circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 14
--

12

Replace the rear quarter window switch. Refer to Quarter Window Switch Replacement .
Did you complete the replacement?
Go to Step 14
--

13

Replace the appropriate rear quarter window actuator. Refer to Body Side Window Actuator Replacement .
Did you complete the replacement?
Go to Step 14
--

14

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Sep 28, 2015 | Pontiac Cars & Trucks

2 Answers

How do i open and close rear windows


Is the safty switch ingaged. Some switches are on the drivers side window and door lock control panel and sometimes its on the end of the door itself so it's not accessible from inside the car.

Dec 01, 2014 | 2004 Ford Freestar

1 Answer

The electric motor wich opens the door is making some clicks while opening and keeps clicking continuously when it reach the end. What can be the problem and how do i fix this?


you must lube and see if there are some parts loose or broken. However you must test the motor for to see if is defective. go to www.aa1car.com get the topic and fix it.
God bless you

Nov 20, 2013 | 1995 Nissan Altima

1 Answer

Rear passenger door won't stay closed


Door latch on door itself is in closed position if it will not close at all. In this case, open door and pull outside handle hard to pop open door latch. If you have door opening at random, door latch needs replacing or door catch on body is loose.

Jul 29, 2012 | 2003 Chevrolet TrailBlazer

2 Answers

Rear passenger door will only open a few inches. Have to manually finish opening and closing.


I'd bet the motor burnt out. If you pull the handle and it opens a few inches, and makes a soun like the door is locked, you might have to get the motor replaced. You probably bought it defective. My 2005 Honda odessy has that same problem from wear and tear.

Aug 22, 2011 | 2005 Chrysler Town & Country

3 Answers

The rear lift gate on my 2006 Lincoln Navigator will not open automatically or manually and there appears to be no way to access anything inside the door from inside or out.


POWER LIFT-GATE OPERATION - To open the optional power liftgate, push the button on the instrument panel , press on your five-button key fob (if equipped), or press and release the control located in the left rear quarter panel (Figure B). To unlatch the liftgate glass, push the button ) under the center of the license plate lamp shield, or press on your five-button key fob. Do not open the liftgate or the liftgate glass in a garage or other enclosed area with a low ceiling. Keep clear of the liftgate when operating the rear switch. To open the liftgate manually, pull the handle located on the liftgate to release the liftgate from the vehicle. The power system will take over when you release the handle. To close, make certain the rear window is closed, and then pull down the liftgate a few inches to activate power closing. Closing the gate rapidly or more than a few inches may activate the obstacle detection feature and stop the power system.------------ Also click this link for more help:--- http://technoanswers.blogspot.com/2011/05/power-liftgate-on-will-not-open-on.html ------------ This should help.Keep updated.Thanks.Helpmech.

May 19, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

How to replace rear blower motor motor in 2006 chrysler town and country van


from autozone.com:


Removal & Installation

  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.


jturcotte_39.gif
Fig. Removing the trim panel to access the rear blower motor

i. Disconnect the wiring harness connector from the accessory power outlet, if equipped.


j. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.


k. Pull first rear seat belt through the access hole.


l. Remove the quarter trim panel from the vehicle.



3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).


4. Twist the blower motor out of scroll housing.


5. Disconnect the blower motor wiring connector.


6. Remove the blower motor from vehicle.

jturcotte_40.gif
Fig. The rear blower motor is held in place by four screws
To install:

  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Nov 04, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

How to replace the blower motor in a dodge 2001 caravan


Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1549e60.jpg

      Fig. Removing the trim panel to access the rear blower motor

    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    823bf07.jpg

    Fig. The rear blower motor is held in place by four screws


To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember to rate this).

Nov 01, 2010 | 2000 Dodge Caravan

1 Answer

Where is the blower motor resistor in a 2001 dodge caravan se. I do not see it behind the glove box. I do see soemthing similar under the hood on the passenger side aginst the firewall but it is not...


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.

    a1b7373.jpg
    Fig. The blower motor is located behind the glovebox, behind the blower motor cover
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting screws.

    bdc6158.jpg
    Fig. Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

    063bc30.jpg

    Fig. The blower motor is secured to the housing with three small screws
  7. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.


Auxiliary Heater and Air Conditioner
Blower Motor - Removal & Installation
  1. Disconnect and isolate the negative battery cable.
  2. Remove the right quarter trim panel as follows:
    1. Remove first rear seat. Remove the second rear seat, if equipped.
    2. Remove the sliding door sill plate.
    3. Remove the quarter trim bolster.
    4. Remove the upper C-pillar trim and D-pillar trim panel.
    5. Remove the first and second rear seat belt anchors.
    6. Remove the screws securing the quarter trim to quarter panel from the bolster area.
    7. Remove the screws securing the rear edge of the quarter trim to the support bracket.
    8. Carefully disengage the hidden clips securing the front of the quarter trim to the quarter panel just rearward of the sliding door opening.

      1dc958e.jpg
      Fig. Removing the trim panel to access the rear blower motor
    9. Disconnect the wiring harness connector from the accessory power outlet, if equipped.
    10. On long wheelbase wagons only, remove the quarter trim from the quarter panel and pull second rear seat belt through access hole.
    11. Pull first rear seat belt through the access hole.
    12. Remove the quarter trim panel from the vehicle.
  3. Remove the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  4. Twist the blower motor out of scroll housing.
  5. Disconnect the blower motor wiring connector.
  6. Remove the blower motor from vehicle.

    1e2cfdc.jpg
    Fig. The rear blower motor is held in place by four screws
To install:
  1. Install the blower motor unit into the vehicle.
  2. Reconnect the blower motor wiring connector.
  3. Secure the blower motor into scroll housing.
  4. Install and tighten the 5 screws mounting the A/C-heater blower motor housing to the rear HVAC unit (one mounting screw located on evaporator cover).
  5. Install the right quarter trim panel as follows:
    1. Install the quarter trim panel in position in the vehicle.
    2. Insert and pull the first rear seat belt through the access hole in quarter trim panel.
    3. On long wheelbase wagons only, insert and pull the second rear seat belt through access hole in quarter trim panel.
    4. Reconnect the wiring harness connector to the accessory power outlet, if equipped.
    5. Engage the hidden clips to secure the front of quarter trim to quarter panel rearward of sliding door opening.
    6. Install the retaining screws that secure the rear edge of quarter trim to support bracket.
    7. Install the retaining screws that secure the quarter trim to the quarter panel in bolster area.
    8. Install the second rear seat belt anchor (if equipped), and the first rear seat belt anchor.
    9. Install the D-pillar trim panel and upper C-pillar trim.
    10. Install the quarter trim bolster.
    11. Install the sliding door sill plate.
    12. Install the second rear seat, if equipped, and install the first rear seat.
  6. Reconnect the negative battery cable. Check blower motor operation.

Hope helps (remember rated this).

Jul 11, 2010 | 2001 Dodge Grand Caravan

1 Answer

Stuck rear window


To remove the door panel there will be 2-5 screw bolts in places like the door handle and behind switch and handle panels. Remove them then teh panel will either lift straight up or pop out if it is held with panel plugs then use a flat pry tool to pop them out.

It does sound like the regulator which is cable driven and will by basiclly held on the glass and the door with bolts. You will need to move the old motor to the new part.

Feb 23, 2009 | 1997 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...